Parts for Thermador PRD366GHC/08: Manifold Parts

This bracket secures internal components and panels to restore proper alignment and reduce vibration. It's a simple replacement that helps stabilize appliance parts for safe, quiet operation. What it does

• Provides a mounting point to hold panels, trim, or internal assemblies in place
• Prevents rattling or vibration caused by loose or damaged supports
• Restores proper alignment so doors and panels fit and operate correctly
• Helps maintain structural stability after repair or component replacement

• One bracket

• Disconnect power (and water if applicable) before starting any repair
• Use appropriate tools; retain all original fasteners unless replacement is specified

This gas pressure regulator controls and stabilizes incoming supply pressure to the appliance manifold, helping ensure consistent burner flames and reliable ignition. Replace if the original regulator is sticking or no longer maintaining correct pressure.

• Regulates incoming gas to the appliance's rated manifold pressure
• Helps maintain even flame height and proper combustion
• Supports reliable burner ignition and reduces flame-out from pressure swings
• Common symptoms include weak or uneven flames, yellow tipping, burners not lighting or not staying lit, or flames that are too high

• Disconnect electrical power and shut off the gas supply before servicing
• Observe the flow-direction arrow; install with outlet toward the appliance manifold
• Use approved gas-rated thread sealant on male threads only and leak-test all joints with a non-corrosive solution after installation

Replacement tube that routes water between appliance components to restore proper flow and prevent leaks. Use this direct-fit tube to replace cracked, brittle, or clogged tubing and stop pooling or improper drainage. What it does:

• Routes water between system components to maintain correct flow
• Prevents leaks and water damage when intact and properly connected
• Helps eliminate pooling, poor draining, or intermittent water delivery caused by damaged tubing
• Fits in-line as the OEM-specified channel for fluid transfer in the appliance

• Disconnect power and shut off the water supply before starting any repair
• Inspect adjoining fittings and seals; replace any damaged clamps or gaskets for a leak-free connection
• Slide the tube fully onto fittings and secure with the correct clamps or fasteners
• After installation, restore power and water, then run a short cycle to check for leaks

Replacement water inlet valve that controls an appliance's incoming water flow for reliable fill and cycle operation. Replacing a faulty valve can stop no-fill, slow-fill, or continuous-fill issues and restore normal performance. What it does:

• Opens and closes to regulate water entering the appliance during fill cycles.
• Helps ensure correct water levels for proper washing or rinsing.
• Common symptom fixer for appliances that won't fill, fill slowly, or keep filling.
• May cause visible leaks at the valve or trigger fill-related fault behavior if failed.

• Turn off power and shut off the water supply before starting any work.
• Open a cycle or relieve pressure to drain residual water before removing the old valve.
• Inspect and replace any worn seals or inlet hoses when installing the new valve.
• Follow the appliance service manual for specific removal/installation steps.

This potentiometer is the rotary sensor behind the control knob. It converts knob rotation into an electrical signal the control board uses to adjust settings, restoring smooth, accurate response when a worn or erratic control causes inconsistent operation.

• Translates knob rotation into a variable-resistance signal for the electronic control
• Enables the control board to regulate power/heat or speed, depending on model
• Common failure symptoms: unresponsive or jumpy settings, dead spots when turning, or settings that drift
• Helps restore precise, repeatable adjustments at the knob

• Disconnect power to the appliance before servicing
• Pull off the knob and open the control panel to access the potentiometer
• Move wires one at a time to the new part; align the shaft/flat to the knob as noted
• Reassemble and test full range of adjustment; follow any model-specific calibration if required

This potentiometer is the rotary sensor behind the control knob. It converts knob rotation into an electrical signal the control board uses to adjust settings, restoring smooth, accurate response when a worn or erratic control causes inconsistent operation.

• Translates knob rotation into a variable-resistance signal for the electronic control
• Enables the control board to regulate power/heat or speed, depending on model
• Common failure symptoms: unresponsive or jumpy settings, dead spots when turning, or settings that drift
• Helps restore precise, repeatable adjustments at the knob

• Disconnect power to the appliance before servicing
• Pull off the knob and open the control panel to access the potentiometer
• Move wires one at a time to the new part; align the shaft/flat to the knob as noted
• Reassemble and test full range of adjustment; follow any model-specific calibration if required

This replacement screw secures appliance panels and components in their proper position. Installing this screw restores a solid, factory fit and helps prevent vibration and misalignment.

• Fastens panels, brackets, or internal parts to the appliance chassis
• Maintains alignment to reduce vibration and rattling noises
• Replaces missing, rusty, or stripped hardware
• Typical symptoms include loose panels, gaps, rattles, or a screw that won't tighten

• Disconnect power (and shut off water or gas, if applicable) before servicing
• Support panels and watch for sharp edges and pinch points
• Use the correct driver size/type for your model to avoid stripping
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing