Maytag Washer Dryer Combo Bearing Parts

The Tumbler Bearing Kit is an OEM replacement part for Whirlpool washing machines. It includes multiple replacement glides that support the movement of the wash basket or tub. As it rotates during the wash cycle, the tub experiences friction that the bearings help manage.  For rear drum support rollers, order 12001541. Please note that repair requires two kits.

Symptoms of bad bearings include:

• Excessive noise or vibrations emanating from the tub area
• Difficulty rotating or spinning the tub by hand  
• Visible wear on the bearings
• Premature breakdown of other components due to increased stress

Causes of bearing failure can be normal wear over time from the consistent rotational motion. Using the washer with an unbalanced load can accelerate bearing deterioration.

This OEM Whirlpool kit is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Tub Bearing Kit is an OEM part for Whirlpool washers. It includes all the necessary components to replace the tub bearing which is responsible for supporting the inner tub and allowing it to spin smoothly during the wash cycle. Over time, the bearing may wear out or become damaged, leading to excessive noise, vibrations, or even leaks from the washer.

Causes of a bad tub bearing can include regular wear and tear, exposure to heavy loads or unbalanced loads that put excessive strain on the bearing, or damage due to water leaks.

Symptoms of a bad tub bearing include:

• Excessive noise or grinding during the wash cycle.
• Vibrations or shaking of the washer.
• Leaks from the washer, around the tub area.
• The inner tub not spinning or becoming stuck.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Note: It is advised to replace the Mounting Stem Repair Kit, part number 6-2040130 at the same time.  To complete the repair, you’ll also need a Spanner Wrench to complete the repair (TB123B).

The Bearing and Seal Kit is an OEM component for Whirlpool and KitchenAid front-load washing machines. The kit includes 2 center post bearings, 3 agitator shaft seals, and 1 center post seal.

These internal seals help retain lubrication inside the motor shaft housing, while the bearings allow for smooth rotation of critical components like the drive pulley. Continuous belt rubbing and water exposure diminish their lifespan over time.

Symptoms of worn motor seals or bearings include:

• Abnormal vibrations during the wash or spin cycles
• Noisy operation and grinding sounds from the motor
• Difficulty starting or stopping the cycle

This OEM kit is also compatible with Maytag, Jenn-Air, Magic Chef, and select Kenmore models.

This small hardware washer sits under a fastener in the specified assembly to distribute load and maintain proper spacing. Replacing a worn or missing washer helps keep components tight, aligned, and operating smoothly.

• Distributes clamping force to prevent fastener pull-through and damage
• Maintains correct spacing/stack-up in the original assembly
• Helps reduce loosening, vibration, and premature wear at the joint
• Typical signs of trouble include rattling, looseness, or misalignment at the connection point

• Disconnect power (and turn off water supply if accessing a wet area)
• Use your model's parts diagram to locate and install the washer
• Replace one-for-one; reinstall any spacers or clips in the same stack sequence
• Tighten fasteners to manufacturer guidance—do not overtighten

A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:

• Supports axial load on the transmission/gearcase shaft to reduce friction and wear
• Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
• Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
• Helps maintain proper alignment of transmission components for smoother operation

• Disconnect power and water supply and drain the washer before beginning any work.
• Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
• Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.