Parts for Ge JE41A04: 01 - Section1 Parts

This microwave thermostat is a temperature-sensitive safety switch that helps protect the unit from overheating. When the preset limit is reached, it interrupts power to the affected circuit to help prevent damage and erratic shutdowns.

• Monitors temperature at its mounting location and opens the circuit if overheating is detected
• Helps protect internal components from excessive heat
• Common symptoms of a failed thermostat include: unit shuts off during cooking, won't start until it cools down, or has no power/no heat due to an open safety
• Replace if the original tests open when it should be closed

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Microwaves contain a high-voltage capacitor that can retain a dangerous charge; only qualified persons should service and discharge the capacitor
• Note wire locations before removal and transfer connections firmly to the new thermostat
• Mount the thermostat securely and in the same position to ensure proper temperature sensing

A replacement outer case that restores the appliance's exterior housing and protects internal components from dust and damage. Replaces a damaged, dented, or corroded cabinet to improve appearance and maintain safe operation. What it does:

• Covers and protects the appliance's internal parts from debris and physical damage
• Restores the appliance's original exterior fit and finish
• Helps maintain proper airflow and component alignment
• Reduces vibration-related rubbing against internal parts that can cause wear

• One outer case

• Disconnect power (and gas, if applicable) before attempting service
• Remove surrounding panels and components as required to access mounting fasteners
• Handle the cabinet carefully to avoid scratches; use appropriate fasteners and alignment during reassembly

This high-voltage rectifier diode is used in the microwave's high-voltage circuit. It converts AC to DC so the magnetron can produce heat. A failed diode can cause no heat, loud humming, or a blown fuse when starting. What it does:

• Rectifies high-voltage AC to DC to power the magnetron
• Blocks reverse voltage in the HV circuit
• Common failure symptoms can include: runs but doesn't heat; loud hum then shutdown; line fuse blows at startup

• 1 high-voltage diode

• Unplug the microwave and properly discharge the high-voltage capacitor before servicing—dangerous voltage can remain even when unplugged
• Match diode orientation/polarity to the original and ensure a solid chassis ground connection where used
• Route leads and reinstall any clamps/insulators exactly as found; keep wiring clear of sharp edges and hot components
• If the original diode failed, inspect the HV capacitor and transformer for related issues before reassembly

The Microwave Door Switch is an OEM part for GE microwaves, designed to prevent the microwave from operating when the door is open by interrupting the power whenever the door is not securely closed. The door switch is an essential safety feature.

Symptoms of a failing Microwave Door Switch include:

• The microwave not starting or heating
• Running when the door is opened
• Unusual noises when the door is closed  

Causes of a bad Microwave Door Switch can result from repeated opening and closing of the door or slamming that can cause the switch to degrade or become misaligned, leading to intermittent or failure.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Microwave Door Switch is an OEM part for GE microwaves, designed to prevent the microwave from operating when the door is open by interrupting the power whenever the door is not securely closed. The door switch is an essential safety feature.

Symptoms of a failing Microwave Door Switch include:

• The microwave not starting or heating
• Running when the door is opened
• Unusual noises when the door is closed  

Causes of a bad Microwave Door Switch can result from repeated opening and closing of the door or slamming that can cause the switch to degrade or become misaligned, leading to intermittent or failure.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

Ceramic

This lever switch is the replacement actuator that mounts to a control switch to engage or move the switch mechanism. It restores proper mechanical actuation so your control responds when you turn the knob. What it does

• Replaces a worn or broken actuator that engages the control switch
• Allows the control shaft or knob to move the internal switch between positions
• Helps restore reliable on/off or position selection when the original lever is damaged
• Commonly used when the control does not respond or feels loose/stiff during operation

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Remove the control panel or knob per your appliance service instructions to access the switch lever
• Match the new lever to the switch shaft and press or secure per the OEM orientation; do not force or bend plastic parts

This outer door window is the glass panel that covers the front of the appliance door, restoring visibility and protecting internal components. It replaces cracked, chipped, or cloudy outer glass to help maintain appearance and safe operation. What it does:

• Provides a clear, protective outer glass barrier on the appliance door.
• Restores visibility through the door when the original glass is cracked, chipped, or fogged.
• Helps prevent debris and moisture from reaching internal door components.
• Contributes to a finished, factory appearance for the door assembly.

• Disconnect power (and gas if applicable) and follow the appliance manufacturer's safety procedures before starting.
• Handle with care—wear cut-resistant gloves and eye protection when removing or installing glass.
• Removal typically requires separating the door assembly and removing retaining screws or clips; keep all fasteners for reassembly.
• If adhesive, trim or replace old sealant as needed and use manufacturer-recommended replacement parts or sealant.

This washered screw secures panels and internal components where a combined screw-and-washer fastener is required, restoring proper fit and stopping movement or rattling. Simple replacement with the correct fastener keeps assemblies aligned and stable. What it does

• Secures panels, brackets or components where a washered screw is specified
• Replaces missing, stripped or corroded fasteners that allow vibration or gaps
• Helps stop rattling, loose panels or misaligned parts caused by a failed screw
• Provides a sealed bearing surface to distribute load and prevent pull-through

• One washered screw

• Disconnect power and/or water to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid cam-out and fastener damage
• Align parts before tightening and snug; avoid over-tightening which can strip threads or crack plastic