Parts for Bosch B18IF800SP/03: Mounting 2 Parts

The Water Filter is an OEM part for Bosch refrigerators. This part removes impurities and contaminants from the water supply to your appliance. This part ensures that the water and ice dispensed by your refrigerator are clean, taste fresh, and are free of common waterborne particles and substances. 

Over time, the water filter can become clogged with sediments and contaminants, reducing its effectiveness and potentially affecting the taste and quality of the water and ice. Regular replacement is essential for maintaining optimal performance.

Symptoms of a bad Water Filter include:

• Unpleasant taste or odor in the water or ice
• Decreased water flow to the dispenser or ice maker
• Visible particulate matter in the water or ice cubes

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This replacement door gasket creates a watertight seal along the dishwasher door to help prevent leaks and maintain wash performance. It restores the door seal surface where cracks, hardening, or compression allow water to escape. What it does:

• Seals the door perimeter to keep wash water inside the tub
• Helps maintain proper water pressure and spray pattern by preventing leaks
• Replaces worn, torn, or hardened gasket material that can cause puddles or damp flooring
• Reduces the chance of water damage to cabinetry from door-area leaks

• One inner door gasket / seal as shown

• Follow manufacturer instructions; door-panel removal may be required for access
• Inspect door edges and latch area for damage before installing new gasket
• Ensure gasket is seated fully in the channel and trim excess if specified by OEM
• Disconnect power and water supply and take standard safety precautions before servicing

This rubber seal replaces a worn or damaged door gasket to restore a tight closure and reduce leaks. It fits the appliance's door/tub opening to help maintain proper water containment and cleaning performance. What it does:

• Creates a watertight barrier between the door and tub to prevent leaks
• Helps maintain consistent internal spray and wash performance
• Reduces water buildup and prevents damage from escaping moisture
• Addresses symptoms such as visible gaps, water on the floor, or a loose/warped door edge

• Recommend disconnecting power and turning off water before beginning any work
• Inspect mounting channel and surrounding area for debris or damage before installing
• Press the seal evenly into the door/tub channel; avoid stretching or twisting the gasket

This factory replacement fixture is the mounting/housing component that holds a corresponding part securely in place inside your appliance. Replacing a cracked or damaged fixture restores proper fit, stability, and dependable operation.

• Provides a stable mounting point for the original component within the unit
• Maintains alignment and spacing per factory design
• Replace if tabs are broken, threads are stripped, or the part no longer holds securely
• Helps resolve looseness, rattling, or components shifting out of position

• Disconnect power before servicing; turn off gas/water if applicable
• Note the orientation and hardware; take photos to aid reassembly
• Transfer any reusable seals or grommets from the old fixture if present
• Reinstall using original fasteners and do not overtighten to avoid cracking

Replacement fixture that secures internal components and mounting points in compatible Bosch appliances. Restores proper alignment and reduces wobble and noise for more stable, reliable operation. What it does:

• Secures and aligns panels, racks, or assemblies to factory mounting points.
• Prevents loose or rattling parts that can cause noise or shifting during use.
• Use when the existing fixture is cracked, broken, missing, or no longer holds parts firmly.
• Helps maintain proper component fit and reduces wear from excessive movement.

• Disconnect power to the appliance before starting any repair.
• Remove any obstructing panels or components to access the mounting area.
• Install with the original fasteners; tighten snugly but do not overtighten.

This fixture is the replacement mounting bracket that secures internal components and assemblies in place, restoring correct alignment and reducing movement. It's a direct-fit service part when the original bracket is cracked, bent, or missing. What it does:

• Provides structural support to hold components firmly in the appliance chassis.
• Helps stop rattling, vibration, and parts shifting that can cause noise or misalignment.
• Restores correct alignment so connected parts operate smoothly.
• Prevents further wear or damage caused by a loose or broken support.

• Fixture (single mounting bracket)

• Disconnect power and water (if applicable) before starting work.
• Use basic hand tools; keep original fasteners or replace with equivalent hardware.
• Inspect mating surfaces and replace any damaged clips or screws to ensure a secure fit.

This replacement fixture mounting bracket secures internal components and panels in compatible Bosch appliances, helping restore proper alignment and reduce rattling or movement from loose hardware. Use it to maintain fit and stable operation of affected assemblies. What it does:

• Secures and supports internal panels, trim, or component assemblies to the appliance frame
• Restores alignment and reduces vibration or rattling caused by loose or damaged mounting points
• Replaces worn or broken hardware that can allow gaps, misalignment, or intermittent contact
• Works as part of the appliance's mounting system to keep moving parts stable during operation

• Disconnect power (and water supply for appliances that use water) before beginning any repairs
• Basic hand tools are typically required; follow the appliance service manual for exact fasteners and steps
• Retain original fasteners and match the part number to ensure correct fit; do not force parts into place

A small metal retaining pin that secures and locates components inside compatible Bosch appliances, helping keep moving parts aligned and preventing unwanted wobble or separation. What it does:

• Holds components or assemblies in the correct position to maintain normal operation
• Prevents parts from shifting, rattling, or binding during use
• Commonly associated with symptoms such as loose panels, noisy operation, or misaligned parts
• Serves as a simple mechanical fastener in hinges, levers, or linkage assemblies

• Disconnect power and water (if applicable) before starting any repair
• Remove any covers or assemblies blocking access; keep track of screws and small parts
• Press or tap the pin into place as OEM orientation requires; use pliers or a soft-faced mallet if needed

A small retaining pin used to secure moving or joined components so assemblies stay aligned and operate properly. Replaces a worn or missing pin to restore secure attachment and reduce rattling or misalignment. What it does:

• Secures two parts together to prevent separation during normal use
• Maintains alignment for hinges, slides, or racks to operate smoothly
• Stops excess movement that can cause noise or wear
• Useful when a pin is bent, broken, or missing and causes loose components

• Recommend checking the mating parts for wear or damage before installing the new pin
• Install with proper tools and ensure the pin fully seats and any retaining clips or fasteners are secured
• Disconnect power or move appliance to a safe position as needed to access the part