Mtd Black Engine Parts

A fuel cap assembly is a component often seen on lawnmowers and other lawn and garden equipment. It is made of durable black plastic and is used to ensure that fuel doesn’t spill out of the fuel tank. Over time, fuel cap assemblies can begin to wear out and cause problems. Sometimes this results in a cap that doesn’t tighten all the way or there may be a fuel smell when using a lawnmower or snowblower. If fuel is leaking, the cap doesn’t fit right, or the cap seems damaged, it’s best to replace it with a new component. This is a simple process that involves removing the original fuel cap assembly and fitting the new assembly to the lawn machine. This fuel cap assembly is a genuine OEM component that comes directly from the manufacturer. It is an individual part that is compatible with MTD, Murray, Cub Cadet, Bolens, Yard-Man, and Yard Machines lawnmowers, snowblowers, chipper shredders, and tillers. No tools are required to replace this component.

The carburetor gasket plate creates a seal between the air cleaner base and the carburetor body. This plate is made of durable material but it is exposed to constant pressure and heat, which can cause it to degrade over time. It can also become damaged or broken, which would require a replacement. If the gasket is degraded or damaged, it could allow air to leak out of the engine, reducing compression and affecting performance. Severe cases could result in total engine failure, which is why replacement should be done as soon as possible. This genuine OEM gasket plate is designed to be used in a variety of log splitters, tillers, and lawn mowers from brands like Yard Machines, MTD, Yard Man, Cub Cadet, Troy-Bilt, and Husky. This carburetor gasket plate is made of durable materials and sold as an individual piece. No hardware is included for this part and will require an additional purchase if needed. Always allow the engine to cool before performing repairs and wear gloves for hand protection.

A gas powered engine often requires priming before it can run, which means injecting some of the fuel into the engine's carburetor. Here, a careful balance of air and gas will receive a spark that causes combustion. The most common way to prime an engine is to use a primer assembly that is activated by a bulb that is pressed to create suction and draw fuel into a reservoir or carburetor. This replacement fuel bulb is for snowblowers that rely on gas powered engines to run. The fuel bulb is very flexible and made to endure seasonal conditions. It works with Craftsman, Yard Machines, MTD, Troy Bilt, and Bolens snowblowers. This is an OEM replacement part that fits into the cover assembly and which requires only a wrench to replace and install. It is sold individually, and other components of the priming assembly may be needed.

This recoil spring and pulley assembly is used in a variety of small gasoline engines that power devices such as mowers, lawn tractors, and log splitters, among other yard and landscaping devices. The assembly works by tightly coiling the spring in the starter housing. When the starter rope is pulled, the tension on the spring is suddenly released, creating a spark that fires the air/fuel mixture. The combustion starts the engine. The constant tightening and releasing of the tension at times will cause wear on the spring, resulting in the need to replace the spring and pulley assembly. To replace the recoil starter assembly, begin by removing the housing. Next, untie or starter rope and check to see if it is frayed and needs to be replaced as well. Remove the old assembly and install the new unit. Remember when re-tensioning the spring to wind the pulley in the opposite direction. Holding the pulley tightly so the spring does not release, attach the cap. Reattach the rope and coil it around the pulley. It is advisable to wear gloves for this task because the pulley and springs have sharp edges. This OEM certified replacement assembly is compatible with Yard-Man, Husky, Cub Cadet, MTD, Yard Machines, and Troy-Bilt yard equipment.

The primer bulb is a small plastic piece that will draw fuel from the fuel reservoir and into the carburetor when it is pressed down. This ensures that the fuel can get into the carburetor so that combustion can happen in the engine. If the primer bulb is broken or damaged on the engine, it will mean that the carburetor will not be getting the fuel it needs to get the engine to start. In some cases, the engine might not start at all. Other times, it might take a while to get the engine to start. These could indicate that it is time to replace the bulb. This is an OEM replacement part that is sold individually. It will work with lawnmowers and other types of small engines. The bulb is compatible with a range of different popular brands including Toro, Kawasaki, Cub Cadet, MTD, and Craftsman.

This is a recoil starter assembly for lawn and garden power equipment. When the recoil starter rope is pulled, this causes the spark which starts the engine.A new recoil starter assembly will be needed if the recoil or pulley system has broken. The rope may become broken or frayed and the plastic on the pulley could crack. If the rope becomes loose and there is no tension when it is pulled, then a new recoil starter assembly will be needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. It is used on engines, lawnmowers, lawn tractors, and log splitters that are manufactured by MTD, Yard-Man, Yard Machines, Cub Cadet, Husky, and Troy-Bilt.

This replacement fuel tank is an authentic OEM part for a lawn mower. The fuel tank attaches to the exterior of a lawn mower and allows the appliance owner to top up their mower with more fuel. Fuel is then passed from the tank to the carburetor through a fuel line. Fuel tanks are made of durable reinforced plastic but because they are located on the outside of the mower, they are susceptible to physical damage. If something heavy were to fall on the fuel tank, it could be dented or even punctured. A damaged fuel tank will leak gasoline on the mower body, creating a potential fire hazard. In this situation, the tank should be drained and then unbolted and replaced. Be sure to remove the fuel line before unbolting it from the mower. This replacement fuel tank is a top of the line part sourced from its original manufacturer. It is compatible with lawn mowers made by MTD, Huskee, Cub Cadet, Bolens, Yard Man, Yard Machines, and Troy-Bilt. This part does not include a fuel cap or a grommet. These parts are sort separately.