Mtd Pro Snow Removal Equipment Parts

The snowblower auger cable initiates operation of the snowblower’s auger similar to the cable on the handle of a push mower. To start the snowblower, the control handle must be squeezed. This engages the snowblower auger cable to allow the auger to begin turning. When the snowblower auger cable is broken, the snowblower cannot work because the auger will not turn. The length of this snowblower auger cable is 47.48 inches. It is made from high-quality rubber insulation of a metal wire. A pair of pliers and a wrench are needed to complete the repair. If the snowblower still does not work after replacing the snowblower auger cable, check the shear pin as these are prone to breaking and will also prevent the auger from turning. This genuine OEM snowblower auger cable is compatible with snowblowers manufactured by Craftsman, Cub Cadet, Husky, MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually. You will need to order any hardware, housing, and the trigger separately if these items also need repair or replacement.

This part is a speed select cable. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or detached speed select cable on certain snowblower models. The speed select cable works by fastening the ground drive system to the speed control level. This enables the equipment operator to properly control speed and traction while using a snowblower. Over time, speed select cables can experience wear and tear which can cause them to break or become detached, requiring replacement. Without a functioning speed select cable, the snow blower will not be able to be properly controlled. For accurate information on how and where to install this replacement speed select cable, specific manufacturer diagrams should be referenced. Proper safety measures should always be followed when working on any type of equipment.As an authentic replacement part, this speed select cable can be used on multiple different models of Craftsman, MTD, Yard-Man, and Huskee snow blowers. Please note that this speed select cable is a genuine part made of high-quality materials and is sold individually.

The friction wheel for a snowblower is sometimes also known as a friction disc or a friction ring. The friction wheel is what helps to move the snowblower forward. When the disc is in contact with the spinning drive wheel, the disc will rotate and turn the axle to propel the snowblower. Over time, the friction wheel can start to wear down or even break. If this happens, it will mean that the snowblower will move slowly, or that it might have erratic movements. Owners who find that they are having similar problems with their machine will want to check the friction wheel to see if it is damaged or broken. They will need to replace the disc before they can use the machine efficiently and safely. The genuine OEM replacement friction wheel is for use with snowblowers, and it is sold individually. Compatible brands include Cub Cadet, Craftsman, Troy-Bilt, Yard-Man, Montgomery Wards, Bolens, Huskee, MTD, Yard Machines, and Ryobi.

The auger belt is a rubber v-belt that goes around the auger on two-stage snow throwers. The belt is responsible for helping ensure smooth rotation of the auger. Since it is made from rubber, it can wear out over time and snap off or become so damaged that it doesn’t work effectively. Replacement of the belt is a part of routine maintenance that comes with snowblower ownership. The belt can be replaced in no time using a basic wrench set. This auger belt is compatible with several snow throwers, including models from MTD, Cub Cadet, Husky, Troy-Bilt, Yard Machines, and Yard-Man. It works with hundreds of different machines and is made from a durable rubber material.

This lower chute is a quality replacement part that is used on several models of snowblowers. It is made of high-quality plastic for durability and is placed so it can direct snow in a certain direction when it leaves a snowblower. Over time and with regular use, this part can become damaged. If this occurs, it will need to be replaced so the discharged snow ends up in the right location.When replacing the lower chute, a wrench and work gloves will be needed. The snowblower should be placed on a flat surface, and the spark plug wire needs to be disconnected. The gearbox and the lower chute will need to be removed before the new replacement part can be installed. Line up the chute and install it used the cotter pin and flange lock nut. Replace all the components before using the snowblower.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold on an individual basis. The lower chute is used with snowblowers manufactured by Craftsman, Cub Cadet, Huskee, MTD, Troy-Bilt, Yard Machines, and Yard-Man.

The shave plate, also called the scraper bar, is an important but often overlooked part of a snowblower. This thin metal strip sits at the bottom of the auger housing against the ground and gathers the snow the auger will expel through the chute. Made of hard plastic, the shave plate is the only part of the snowblower that actually touches the snow-covered ground without rolling. As durable as the shave plate is manufactured to be, it constantly comes into contact with unseen objects that pound, slice, and pit it. Eventually, the shave blade has to be replaced. To replace the blade, simply invert the blower, unscrew the old blade, attach the new blade, and put the blower right side up again. As long as the user is replacing the shave plate and has the machine upside down, this is an ideal time to check for damage to the wheels, the auger blades, driveshaft, and the condition of the shear pin. If this replacement is taking place in preparation for the coming winter, it might be a good time to replace the oil and oil filter as well. Be sure to use genuine OEM replacement parts that perfectly match the factory originals. This blade is compatible with snowblowers made by Yard-Man, Bolens, Yard Machines, Troy-Bilt, Craftsman, Ryobi, Cub Cadet, Huskee, Montgomery Wards, and Ryobi.

In a snowblower, the driveshaft is connected to a part called a worm gear. The worm gear turns the auger blades which eject the snow. The worm gear is connected to the worm shaft, which causes the auger blade to turn rapidly. Eventually, the incredible torque inside the machine, plus the occasional bumps and bruises experienced by the machine in operation and when being stowed, may cause the worm gear to malfunction. When the snowblower is erratic in its operation and fails to remove snow completely, there is a good chance the problem is the worm gear. To replace the worm gear, remove the housing to get to the worm shaft. Remove the entire worm assembly. Next, remove the blower fan and remove the worm gear. Grease the auger assembly before installing the new gear. Reverse the order to reassemble. While the snowblower is disassembled, it's the best time so exam the auger, driveshaft, sheer bolts, and tires for wear. You may find other parts that need to be updated. Make sure to replace the worm bolt and any other necessary parts with a genuine OEM manufactured part such as this one. This gear can be used in a number of snowblowers, including machines made by Yard Machines, Craftsman, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, Ryobi, Montgomery Wards, Huskee, and MTD. Part sold individually.

This is a genuine MTD fuel cap replacement made for use on select snowblowers. It features a molded gasket for secure sealing and less risk of losing parts. The fuel cap is responsible for securing the fuel in the fuel tank during operation so that it doesn't spill out. There is an air hole in the cap to prevent pressurization of the fuel, ensuring safe operation at all times. This cap is made of plastic and it can become cracked or stripped with regular use. If it is damaged, the fuel will not be secure and the machine will not be safe to use. That will require an immediate replacement. This OEM fuel cap is made to exact standards by MTD and is compatible with several models of snow blowers and snow throwers. It is also capable of fitting select models from Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. It features an easy plastic grip and a seal to prevent spillage. It can be installed with no tools and is sold as an individual unit. It is easy to screw the new cap into place, but be sure to thread the screw properly to prevent accidental stripping or misthreading that can cause the cap to get stuck.

The snowblower auger paddle is designed for use with various single-stage 21 MTD snow throwers and blowers. This part may also be referred to as the spiral crescent. This paddle is attached to the auger, which rotates when the engine is started. As the auger rotates, the paddle will pick up and throw the snow out of the way. This part may get damaged by debris or some type of accident, or it can wear down over time. Replace a broken or worn out snowblower paddle with a genuine OEM replacement paddle. This is an OEM replacement part from MTD that fits various models of snowblowers. It can be used with compatible models from Yard Machines, Yard-Man, Troy-Bilt, Husky, Ryobi, Bolens, and MTD machines. There are over 150 models in total that this paddle can work with. It is made out of durable rubber and comes sold individually. There are two screws at each end required for mounting, which are sold separately.

This is a simple extension spring with an outside diameter of 0.38 and a slack length of 2.5. It is primarily used as an extension spring for snowblowers, but may be compatible with other lawn equipment. It’s designed to apply tension as the throttle is applied. The more gas there is, the more resistance will be present. Under most circumstances, replacement is easy. When the spring breaks or gets rusty, look at both points of attachment. Memorize where it’s attached, or take a picture, and remove the old spring using a pair of pliers if necessary. Install the new spring and the tool is ready to use. This is an OEM part sourced directly from MTD, and it is sold individually. It’s black in color and was initially designed for Troy-Bilt lawnmowers. However, because this is a versatile part, it has since been repurposed for a number of MTD and related machines in other brands. These include lawn tractors and snowblowers, as well as lawnmowers, in brands such as Ryobi, Yard Machines, Husky, and Cub Cadet.

This is a durable rubber auger drive belt that is made for use with a selection of snowblowers, specifically walk-behind models. This part is the primary belt in a snowblower for driving the augers that remove snow and clear driveways. Time and use can cause the belts to stretch and wear out. In order to maintain the best possible performance, a worn belt needs to be replaced. In some cases, mechanical issues in the snowblower can also wear the part out more quickly than usual. If the auger drive belt is extremely worn, the snowblower will stop running. The belt can even slide off of the pulley and prevent the machine from working correctly. This can also cause the snowblower to stop running.This auger drive belt is an authentic OEM replacement part that is directly sourced from the manufacturer. It comes as an individual part. It can be used with snowblowers manufactured by Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, MTD, Huskee, and Yard-Man.

This genuine OEM replacement part is an extension spring for a Craftsman snowblower idler pulley assembly. The idler pulley attaches to a part of the snowblower's housing and is helps to transfer energy throughout the belt drive. This extension spring helps to redistribute some of the back-and-forth motion created in the pulley as the snowblower runs. This keeps the assembly from shifting out of place and potentially slipping. This extension spring is attached at two points and, if pulled in both directions too far, can eventually lose some of its tension. When this happens, the idler assembly can begin to shake and even slip out of place. Replacing the extension spring is an easy job that will only require a socket wrench to remove the idler pulley. A pair of pliers may help to remove the spring from its clips. This part is only compatible with Craftsman snowblowers and is sourced from its original manufacturer. It ships individually and any additional parts needed will have to be purchased separately.