Mtd Pro Snow Removal Equipment Parts

This is an MTD rocker arm. The rocker arm works in conjunction with the engine and head. The job of the rocker arm is to push the intake valve open, allowing fuel and air to enter the cylinder. Since the rocker arm is a part of the head gasket system, any damage can cause the engine to run extremely weak. There could also be a noticeable clicking or ticking noise originating from the engine area of the mower. A visual inspection of the rocker arm will confirm any damage. Begin the repair by removing the muffler guard. After removal, move to the valve cover and remove that guard as well. Disconnect the fuel and air lines running to the head. Remove the spark plugs in the valve section. Finally, the rocker arm can be removed using a socket wrench. Repeat these steps in reverse to install the new rocker arm.This product is sourced directly from the manufacturer as a genuine OEM part. The component is available individually, separate from the original machine. This part is compatible with MTD and Cub Cadet brand equipment.

Seals the intake valve to prevent oil leaks and maintain proper compression in small engines. Replace if you notice oil consumption or performance loss.

Carburetor insulator gasket installs between the carburetor and engine block. Replace if cracked, deteriorated, or missing to prevent air leaks.

Engine losing compression or making knocking sounds? This piston pin snap ring secures the piston pin in place. A small but critical engine component.

Fix engine knocking or loss of power with a new piston pin. Essential for connecting the piston to the connecting rod in small engines. Simple repair.

Intake valve seal prevents air and fuel from escaping during engine operation. Replace if you notice oil consumption or reduced performance. Verify fit with your engine model number before ordering.

This genuine MTD replacement part is a rocker arm for use with snowblowers, lawn tractors, and other equipment with an engine. A properly functioning rocker arm is essential for the safe and reliable use of the equipment. The rocker arm works to open the intake and exhaust valves. The rocker arm may become worn out or damaged with extended use, necessitating replacement. Remember to check the rocker arm periodically to spot any wear or damage. This part is an identical replacement for a rocker arm that is missing, worn out, or damaged. Prior to working with this part, please refer to the original product manual for a full list of included parts and installation instructions. A wrench set may be required for installation of this part. For safety, always wear gloves and ensure unit is powered down and cool prior to performing any installation or repair.This high quality OEM replacement part is sourced directly from the manufacturer, and it is sold individually. It is made of high-quality durable metal. This part is compatible with a variety of MTD, Yard Machines, Troy-Bilt, Yard Man, Cub Cadet, Husky, and other equipment. Please note: original part numbers 1843974, 751-11966 is now obsolete, and manufacturer has replaced the original part numbers with this part.

Replaces a worn, damaged, or missing valve spring retainer in your outdoor power equipment engine. Essential small fastener component for valve assembly.

If your engine runs rough or won't start, the exhaust valve adjuster may need replacement. This part ensures proper valve clearance for optimal performance.

Stator for gas snow throwers. Mounts to the engine to generate power for lights or battery charging. Replace if cracked, damaged, or missing.

Fix engine starting problems or loss of compression with this valve spring. Controls valve timing in small engines. Common repair for lawn tractors and snow throwers.

This flywheel mounts on the engine crankshaft and provides the rotational mass needed to keep the engine running smoothly between power strokes. It also contains magnets that work with the ignition coil to generate spark. Replace the flywheel if the engine won't start due to a damaged keyway, if you notice a sheared flywheel key after hitting an obstruction, or if the magnets are cracked or missing.

Carburetor rebuild kit for snow thrower engines. Includes gaskets and components to restore carburetor function when worn, damaged, or leaking fuel.

If your snow thrower won't start or the pull cord snaps back, the recoil starter assembly likely needs replacement. Moderate DIY repair in 30-45 minutes.

This starter ignites the combustion engine for a compatible, small engine snowblower or chainsaw. When operating correctly, through slight force, the user is able to start the engine and associated components. Replacement becomes necessary if recoil abilities are diminished or if the engine won't start when the starter is engaged.This product is a durable metal and plastic component. Use over time or exposure to an outside environment can cause this part to crack or warp, decreasing the ability to start the machine. Replacement is simple and may require a screwdriver, nut driver, and pliers. Remove the screws from the blower housing to expose the recoil starter. Remove the old recoil starter, and replace with a compatible starter part. Refer to the owner's manual for any specific to model safety guidelines or instructions.This part is compatible with MTD, Craftsman, Cub Cadet model small engine snow blowers and chainsaws. It is also an OEM part sourced directly from the manufacturer, and it is sold individually.

Breather hose for snow thrower engines. Connects engine crankcase to air filter housing for proper ventilation. Replace if cracked, split, or missing.