Mtd Snow Removal Equipment Blade

The shave plate is a common snowblower part that attaches to the back of the blower housing and directs snow into the auger and blade assembly so it can be cleared. The particular layer of ice and snow this blade is removing is the hardest and heaviest part of the snowfall. The shave plate is also called the scraper bar or scraper blade. Periodically, because it is in direct contact with the concrete surface below the snow, the shave plate wears out and must be replaced. A shave plate may be worn, gouged, or sliced so it does not smoothly remove the snow from the sidewalk. Replacing the shave plate is a simple task that can be accomplished in 30 minutes or less. The shave plate is connected to the blower housing by four adjustable fasteners that are removed. This genuine OEM replacement part is manufactured by Genuine MTD. It is compatible with a great variety of snowblowers, including Husky, Troy-Bilt, Yard Machines, MTD, Cub Cadet, and Yard-Man. This OEM part is sold individually.

This scraper blade is an authentic OEM replacement part for a snowblower. Snowblowers operate using an auger that scoops up the snow and blows it to a different location. However, an auger cannot gather all of the snow because it would have to scrape against the ground. Scraping that auger against the ground would damage its blades and make them unusable. Instead, this scraper blade drags against the ground and collects any remaining snow so that the auger blades can remain protected. Scraper blades can be damaged if the snowblower goes over rocky terrain. Although it is nearly impossible for a blade to snap completely off a blower, the blade will leave the snow behind, making the blower less effective if chipped or dented. To replace a scraper blade, simply use a socket wrench to unbolt the blade from the auger housing. Be sure not to lose the bolts as they will be needed for reassembly. This part is compatible with Craftsman, MTD, Cub Cadet, Ryobi, Huskee, Yard Man, and Yard Machines snowblowers and is sourced from the original manufacturer. This part is a high-quality replacement part. It does not ship with additional hardware.

This part is a sheave plate that is used on snowblowers. This part is attached to the auger housing base assembly and its purpose is to scrape snow up into the auger blades. A new sheave plate may be needed if there are any signs of wear or damage of any kind. If the snowblower is leaving behind strips of snow, this can be a sign that the sheave plate needs to be replaced; it's also one of the most common signs of a bad sheave plate. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. This sheave plate is used on snowblowers manufactured by MTD and Craftsman.

This is a replacement shave plate for use with snowblowers. The plate attaches to the bottom of the auger housing on the machine and provides protection for the auger and the housing. If it is broken or not functioning properly, debris could damage these other parts of the snowblower. This would then require a larger repair.The shave plate is made from metal and is durable. However, the nature of the plate is to provide protection, which means it will become dinged and damaged over time. It could become bent if the user hits a large rock or chunk of ice. If there is damage to the snowblower shave plate, the user should be sure to replace it before using the machine again.This snowblower shave plate is compatible with models from Craftsman, MTD, White Outdoor, Ranch King, Yard-Man, and Yard Machines. The plate is sold individually, and it is a genuine OEM replacement part sourced from the manufacturer.

This genuine MTD shave plate, also known as a scraper bar, can be used as a replacement part for snowblowers. The shave plate is located at the bottom of the auger to scrape snow off of surfaces and filter it into the auger of the snowblower.Damage to the shave plate might include cracks, dents, and erosion to the metal material, or it can gradually wear out and no longer be effective. Evidence of a cracked shave plate can come from a visual inspection, but it can also be detected if the snowblower is doing a poor job of collecting and scraping snow off of surfaces. A cracked shave plate should be removed and replaced immediately, and a snowblower should not be used before the part is replaced. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This shave plate is compatible with the following brands: MTD, Yard Machines, Cub Cadet, Yard Man, and Craftsman. Part sold individually.

This part is a shave plate. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a damaged, detached, or worn shave plate on certain models of snowblower. When using a snowblower, stubborn or stuck pieces of snow can affect proper functionality. Shave plates attach to the underside of the snowblower to help scoop stubborn snow or slush into the auger housing. Over time, as they regularly scrape the ground, shave plates will become worn and will no longer make sufficient contact with the pavement. In order to ensure snow blowers continue to do their job efficiently, shave plates should be replaced once they exhibit signs of deterioration. Proper tools are needed to replace this part and appropriate safety guideline should always be adhered to.As an authentic replacement part, this shave plate can be used on multiple different models of snow blowers manufactured by Cub Cadet, Craftsman, Huskee, Troy-Bilt, Yard-Man, and MTD. Please note that this shave plate is a genuine part made of high-quality, durable materials and is sold individually.

This genuine MTD shave plate, also known as a scraper bar, can be used as a replacement part for snowblowers. A shave plate,located at the bottom of the snowblower auger, scrapes snow from surfaces and feeds it into the auger drill.Gradual damage to the shave plate is to be expected in the lifespan of a snowblower, as it bears a lot of the brunt of snowblower work. Damage to a shave plate can be detected from a simple visual inspection for cracks, dents, and erosion to the metal material. If the snowblower is not clearing away snow from surfaces as well as it usually does, it is likely that the shave plate is cracked or damaged. If this is the case, it should be removed and replaced immediately. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This shave plate is compatible with the following brands: MTD, Yard Machines, Cub Cadet, Yard Man, and Craftsman. Part sold individually.