Norge Dishwasher Parts

This tub wheel mounts on the dishwasher's tub wall to guide and support the rack as it slides in and out. Replacing a worn wheel restores smooth rack movement and helps prevent binding, noise, and derailments.

• Mounts to the tub to provide rolling support for the dish rack/rail
• Replaces cracked, flattened, or missing wheels that impede rack travel
• Helps fix racks that stick, bind, are hard to pull/push, or derail
• Reduces grinding or squeaking from the rack area

• Disconnect power at the breaker before servicing
• Open the door and pull the rack forward for access
• Release the old wheel from its retainer/axle per your model's design; install the new wheel in the same orientation
• Ensure the wheel spins freely and the rack slides smoothly before use

A replacement tension spring designed to restore proper movement and return force to the appliance mechanism. Helps the affected component operate smoothly so doors, levers or assemblies move with correct tension and alignment. What it does:

• Provides return and holding tension for the appliance mechanism to restore normal movement.
• Helps reduce sagging, misalignment, or loose operation of the associated door or linkage.
• Minimizes noise and vibration caused by a worn or weakened spring.
• Works as the direct-fit part when the listed part number matches your appliance.

• Disconnect power and water (if applicable) before beginning any repair.
• Springs are often under tension—wear eye protection and use caution when removing or installing.
• Follow the appliance's service manual or OEM instructions for correct orientation and safe installation.

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks

A small replacement retainer clip used to secure exterior trim and interior panels on compatible Whirlpool appliances. Restores proper panel fit and prevents rattling or loose trim for a cleaner, safer operation. What it does

• Secures trim, panels or components in place to maintain proper alignment
• Helps stop rattling, vibration noise and loose-fitting parts
• Keeps seals and covers positioned so doors and panels close correctly
• Simple, single-purpose hardware used where a clip-style fastener is required

• One retainer clip as pictured

• Disconnect power (and water if applicable) before starting any repair
• Remove the surrounding trim or panel to access the retainer; small trim tools may help
• Fasten clip into the OEM mounting hole until it snaps or seats firmly
• Keep removed screws and small parts organized to avoid lost hardware

A replacement appliance door handle that restores a secure grip and proper operation to a worn or broken handle. Designed to match the original mounting style for a clean, factory-fit appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door smoothly
• Replaces cracked, loose, or broken handles that affect normal door use
• Restores correct alignment and leverage to reduce strain on door components
• Helps prevent accidental drops or slippage when grabbing the door

• One replacement handle

• Remove power and empty the door area before starting any repair
• Typical install requires removing trim or screws; use manufacturer-recommended fasteners
• Retain original mounting hardware unless the new handle explicitly includes replacements

The Door Latch Assembly is an OEM replacement part for Whirlpool dishwashers. It securely fastens the dishwasher door closed during wash cycles to contain water, detergent, and wash motions within the tub. This dishwasher door switch assembly does not include the handle. It includes two switches and a holder.

Over time, latch components can wear from continual use and lose their ability to lock the door. Exposure to water and detergent may also cause corrosion or cracking.

Symptoms of a bad door latch assembly include:

• The dishwasher door not closing fully or securely during cycles  
• Gaps around the door allowing water and air leakage
• The door popping or opening unexpectedly mid-cycle
• Dishwasher will not start

This Whirlpool part fits dishwashers from Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and select Kenmore models.

This is a genuine replacement screw used to secure appliance panels and components, restoring proper fit and reducing vibration or rattling. Simple, low-cost fastener that helps keep parts aligned and stable. What it does:

• Fastens panels, brackets, or trim to the appliance frame
• Restores secure connections that can cause buzzing, rattling, or loose trim
• Replaces missing or stripped hardware to prevent further movement or wear
• Works where the original OEM screw was specified for fit and compatibility

• Disconnect power before working on electrical appliances to avoid shock
• Use the correct size driver to avoid stripping the head
• Install by hand initially to ensure proper threading, then snug—do not overtighten
• Retain removed hardware and compare to the new screw for correct fit before final assembly

Color: Black

This O-ring creates a watertight seal in your dishwasher's wash or drain system, helping prevent leaks and maintain proper water pressure. Replace a brittle, flattened, or damaged ring to restore a reliable, leak-free connection.

• Provides a watertight seal between mating parts such as pump housings, fittings, or hose joints
• Helps stop drips and seepage caused by a worn or deformed seal
• Common symptoms: water under the unit, moisture around pump/tubing connections, or leaks after reassembly
• Replace if the old ring is cracked, cut, flattened, or hardened

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water
• Clean the groove and mating surfaces; lightly moisten or use a manufacturer-approved lubricant to help the ring seat without pinching
• Seat evenly, reassemble without overtightening, and run a short test cycle to check for leaks