Parts for Jenn-Air JGRP536WP01: 08 - Optional Parts

Size: 1/3 oz.

This wiring harness routes power and signals between the appliance control and components, restoring reliable electrical connections so controls and motors communicate correctly. It's a direct-replacement harness used where the original is damaged or worn. What it does:

• Carries control and power wiring between the console/control board and components
• Restores lost or intermittent function caused by broken, frayed, or melted wires
• Prevents short circuits from exposed conductors and improves connection stability
• Helps resolve symptoms such as no power to a component, intermittent operation, or visible wire damage

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Follow OEM wiring routing and connector locations; replace only with the identical harness
• Inspect connectors and terminal ends for damage and secure all plugs during reassembly

This conversion kit contains the components needed to change a gas appliance's fuel type so it operates safely and correctly after switching fuel sources. It ensures proper burner/valve configuration for the specified conversion per OEM instructions. What it does:

• Provides the parts required by the manufacturer to convert a gas appliance between approved fuel types so burners burn properly.
• Includes the hardware needed to alter orifices, fittings, or regulator settings as specified by the OEM.
• Helps correct symptoms caused by an incorrect fuel setup, such as uneven flames, poor heating, or ignition difficulties after a fuel change.
• Ensures the appliance can meet correct pressure and flow requirements only when installed per OEM instructions.

• Install only following the manufacturer's conversion instructions; improper conversion can create a safety hazard.
• Shut off gas supply and electricity before beginning, and perform a full leak test after installation.
• Adjust burner flames and check appliance operation per OEM procedure; do not modify parts beyond the OEM conversion kit components.

The Harness-Wire is an OEM part for Whirlpool ranges. It serves as the wiring harness that connects electrical control boards and sensors within the range. 

 Symptoms of a bad harness-wire include:

• Elements or burners that do not heat 
• Issues with switches, controls, or displays failing to work properly
• Recurring range or oven component malfunctions

Causes of a bad harness-wire can be damage from excessive flexing/bending over time, moisture leading to shorts, or failure of crimp/solder connections along the wire.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness routes power and signals between the appliance's electrical components to restore reliable operation and proper control functionality. It replaces a damaged or worn harness to fix intermittent power, control failures, or burnt connectors. What it does:

• Connects control board, switches, motors and other electrical components so they communicate and receive power
• Restores lost or intermittent power caused by broken or frayed wires
• Resolves control or function failures when caused by damaged wiring or connectors
• Prevents arcing and poor connections from worn terminals or insulation

• Disconnect power (unplug appliance or switch off breaker) before any service
• Match connectors and routing to the original harness; secure using existing clips and holders
• Inspect mating connectors and boards for heat damage before installing the new harness

This replacement wire provides a direct electrical connection between appliance components to restore proper function and safe operation. Use it to replace a damaged or frayed lead that's causing intermittent or lost connectivity. What it does

• Carries electrical current between terminals or components to enable operation
• Restores a secure connection when the original lead is cracked, cut, or corroded
• Can stop intermittent power, no-starts, or erratic behavior caused by a damaged lead
• Helps prevent arcing or shorts when a worn wire is replaced

• One replacement wire as shown

• Disconnect power to the appliance before checking or replacing wiring
• Verify terminal orientation and secure connections; use correct connectors and insulation
• Replace only like-for-like wire gauge and routing to maintain safety and performance
• If pins, splices, or connectors are damaged, replace or repair them per OEM guidance

This wok ring is a burner accessory that stabilizes round-bottom woks on gas range grates, letting you use wok-style cookware safely and maintain even heating. Durable design keeps cookware centered over the flame. What it does:

• Supports round-bottom woks and small, curved cookware on a gas burner
• Helps keep cookware stable to prevent tipping and uneven cooking
• Places the wok closer to the flame for improved heat contact
• Fits into the burner grate without tools for simple placement

• Install only on a compatible gas range grate; ensure the range is off and cool before placing the ring
• Position the ring securely in the grate recess so the wok sits level over the burner
• Inspect for cracks or warping; replace if damaged to avoid instability

Size: 2.8 fl.oz tube. 748 non-corosive sealant.

Screws for range anti tip bracket: WP3801F656-51. Includes 2 screws.

This broiler pan restores a sturdy broiling surface in your oven. It holds food for high-heat broiling while the lower tray catches drippings to help reduce smoke and keep the oven cavity cleaner.

• Provides a durable surface for broiling under the broil element or flame
• Collects grease and juices beneath the food during high-heat cooking
• Replaces pans that are missing, warped, chipped, or heavily rusted
• Helps cut down on smoke and mess from burnt-on residue on a damaged pan

• Allow the oven to cool completely before handling
• Slide the pan onto the appropriate rack position per your model's instructions; no tools required
• Use oven mitts—surfaces and edges can be hot after broiling
• If your model uses a separate broiler grid or rack, position it on top of the pan before cooking