Parts for Hot Point DLB1550PC: Other Parts

This dryer motor kit powers the drum and blower. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads more evenly.

• Drives the drum via the belt and turns the blower wheel for airflow
• Helps resolve: dryer hums but won't start, drum won't turn, or stops mid-cycle
• Can reduce loud buzzing/grinding noises from the motor area
• Restores consistent operation when the motor overheats and trips its protector

• Disconnect power; turn off gas supply to gas dryers before servicing
• Remove panels to access the drive system; release belt tension and remove the drum as needed
• The blower wheel threads onto the motor shaft—support it carefully; many GE dryers use a reverse (left-hand) thread
• Transfer wiring and any reusable hardware to the new motor; test before reassembly

The Dryer Drive Belt is an OEM part for GE dryers that connects the motor to the drum, allowing the drum to rotate during the drying cycle. The belt measures approximately 87 inches long and 0.25 inches wide, with 4 ribs.

Over time, the Dryer Drive Belt can wear out or break, leading to the drum not turning.

Symptoms of a bad Dryer Drive Belt include:

• The drum not spinning or rotating
• A squealing or thumping noise coming from the dryer
• The dryer stopping unexpectedly during a cycle

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This idler pulley keeps tension on the dryer drum belt so the motor can spin the drum smoothly. Replacing a worn pulley can quiet squealing and restore consistent tumbling.

• Maintains proper belt tension so the drum turns under load
• Free-spinning pulley reduces friction and belt wear
• Common symptoms of failure: squealing/chirping noises, drum won't turn, belt slipping or fraying, burning rubber smell
• Helps prevent the belt from jumping off the motor or drum

• Disconnect power; for gas dryers, shut off the gas supply
• Access typically requires removing the top/front panel and releasing belt tension to remove the drum
• Transfer any spacers/retainer from the old pulley to the new one; the pulley spins freely before reassembly
• Route the belt per the model's diagram and check belt alignment/tension before test run

This motor drive pulley guides the dryer drive belt and helps transfer motor power to the drum for proper rotation. Replacing a worn or damaged pulley restores smooth drum movement and reduces noise. What it does:

• Guides and supports the drive belt so the drum turns evenly
• Maintains belt alignment to prevent slipping or excessive wear
• Reduces squealing or grinding caused by a damaged pulley bearing
• Helps restore normal tumbling when the drum drags or hesitates

• One motor drive pulley

• Disconnect power to the appliance before any service; follow lockout/tagout best practices
• Inspect the drive belt and bearings while replacing the pulley; replace worn belt or bearings as needed
• Typical service requires basic hand tools and access to the dryer cabinet or motor housing

This dryer motor kit powers the drum and blower. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads more evenly.

• Drives the drum via the belt and turns the blower wheel for airflow
• Helps resolve: dryer hums but won't start, drum won't turn, or stops mid-cycle
• Can reduce loud buzzing/grinding noises from the motor area
• Restores consistent operation when the motor overheats and trips its protector

• Disconnect power; turn off gas supply to gas dryers before servicing
• Remove panels to access the drive system; release belt tension and remove the drum as needed
• The blower wheel threads onto the motor shaft—support it carefully; many GE dryers use a reverse (left-hand) thread
• Transfer wiring and any reusable hardware to the new motor; test before reassembly

The High Limit Thermostat is an OEM part for GE dryers. It is a safety device that prevents the dryer from overheating by cutting off power to the heating element if the temperature exceeds a safe limit. This helps protect the dryer and the user from potential fire hazards.

Causes of a bad high limit thermostat can include electrical faults, repeated exposure to high temperatures, or wear and tear over time. When the thermostat fails, it may either keep the dryer from heating or cause it to overheat.

Symptoms of a bad high limit thermostat include:

• The dryer not heating at all
• The dryer overheating and shutting down mid-cycle
• Clothes taking longer than usual to dry
• The dryer running but not producing any heat

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.