Parts for Ge ZDP366NP2SS: 05 - Oven Cavity Parts

A complete oven rack and guide kit that restores proper rack support and smooth sliding in compatible 48" and 36" ovens. Replaces worn, bent or broken racks and roller/guide assemblies to improve rack stability and function. What it does:

• Provides a full replacement rack plus guide hardware to support cookware and prevent sagging
• Restores smooth, even rack movement when sliding food in and out of the oven
• Replaces bent, warped or damaged rack or guide components that cause sticking or uneven travel
• Helps maintain correct oven clearance and safe placement of cookware while cooking

• Always disconnect power to the oven and allow it to cool before installing parts
• Installation uses basic hand tools; keep fasteners and hardware in a safe place during replacement
• Inspect oven cavity and mounting points for damage and replace any additional worn hardware as needed
• Follow the appliance manufacturer's instructions for correct placement and testing after installation

Restore bright, clear visibility inside your oven with this 20-watt halogen light bulb. Replace a burned-out bulb to monitor cooking through the window and safely see racks and dishes without opening the door. What it does:

• Illuminates the oven cavity when the light switch is used or the door is opened
• Helps you check cooking progress and locate items inside the oven
• Common symptoms: interior light won't turn on, is dim or flickers, or the bulb glass is broken
• 20-watt halogen design matches the original lighting specification

• 1 halogen light bulb

• Disconnect power at the breaker and allow the oven to cool completely
• Wear gloves or use a clean cloth; avoid touching the glass envelope
• Remove the lens/cover per your model instructions; carefully remove the old bulb and fully seat the new bulb
• Reinstall the cover, restore power, and test; use only the wattage/type specified for your appliance

This clip retainer secures the oven door glass to the door frame to keep the glass stable during use and prevent rattling or separation. Simple replacement restores proper glass alignment and reduces vibration noise. What it does:

• Holds the inner door glass in position inside the oven door assembly.
• Prevents the glass from shifting, rattling, or contacting other door parts.
• Helps maintain a safe, stable door assembly after a cracked or missing clip.
• Commonly replaced when the glass feels loose or the door vibrates during operation.

• One clip retainer for door glass.

• Disconnect power to the appliance before starting and allow the door to cool completely.
• Remove the oven door per the manufacturer instructions and handle glass with care — support both pieces of glass when separating.
• Use basic hand tools; keep track of screws and any spacers removed.

This hidden bake element provides the oven's primary lower heating source for baking and roasting. It restores consistent bake heat and is a direct-replacement part used in many GE electric ranges and wall ovens. What it does:

• Heats the oven cavity from the bottom for baking and roasting cycles
• Replaces a burnt-out or non-heating lower element to restore oven temperature
• Helps improve evenness of baking when the original element no longer reaches set temperature
• Commonly used when the oven won't bake or the lower area doesn't get hot

• One hidden bake heating element

• Disconnect power at the breaker or appliance plug before starting any work
• Allow the oven to cool completely and remove oven racks before accessing the element
• Element typically secures with mounting screws and two electrical terminals; support the element while removing/replacing to avoid stress on wires
• After installation, restore power and run a short bake cycle to verify operation

The Oven Temperature Sensor Assembly is an OEM replacement part for GE electric wall ovens. It is responsible for accurately reading the oven's internal temperature to provide precise temperature control and safe operation. Consistent and precise temperature readings are necessary for repeatable cooking results.  

Symptoms of a bad temperature sensor include:

• Inability to reach or maintain set cooking temperatures
• Fluctuating temperatures causing inconsistent results  
• Error codes or fault messages related to temperature regulation
• Potential safety concerns if temperatures run too high or low

Causes of a faulty sensor can be due to failures over extended usage, exposure to high heat cycles, or impedance changes due to dirt or mineral deposits. Precise temperature readings allow for confident cooking.

This OEM GE replacement sensor is also compatible with Hotpoint, RCA, and some Kenmore electric wall oven models. 

This replacement crystal lamp provides the interior lighting for refrigerators, improving visibility so food and shelves are easier to see. Designed as a direct-fit replacement to restore a clear interior light. What it does:

• Illuminates the refrigerator interior to help you find items more easily.
• Replaces a cracked, broken, dim, or missing lamp assembly.
• Fits into the existing lamp housing and works with the original socket.

• Disconnect power to the appliance before starting any work to avoid electrical shock.
• Handle the lamp carefully—wear gloves or use a cloth to avoid cuts from glass.
• Remove old lamp assembly per the owner's manual; align and seat the new lamp securely in the housing.

Probe thermistor (temperature sensor) gives the refrigerator control board accurate internal temperature readings so it can regulate compressor and defrost cycles. Replacing a bad thermistor helps restore steady cooling and correct temperatures. What it does:

• Senses interior temperature and sends the signal to the control board so cooling and defrost cycles operate correctly.
• Fails can cause uneven temperatures, items being too warm or too cold, or intermittent cooling.
• Often used in fresh food and freezer compartments as part of temperature control and defrost systems.
• Electrical symptoms may include inconsistent cycling or the fridge running more than expected.

• Disconnect power before servicing to avoid electrical shock.
• Handle the sensor tip and wiring gently; avoid kinking or crushing the probe or leads.
• Basic hand tools are usually required; check the appliance service manual for access and routing.
• After installation, restore power and confirm correct operation.