Parts for Kitchenaid KEBS277BSS00: 03 - Oven Door Parts

A replacement bumper rail that cushions and stabilizes appliance doors and drawers to reduce noise and prevent metal-to-metal contact. Restores smoother closing and helps protect the appliance finish from wear. What it does:

• Cushions doors/drawers to reduce rattling, banging, and vibration
• Prevents contact between moving parts and cabinet edges that can cause chips or scratches
• Helps maintain alignment for smoother opening and closing
• Common symptom: noisy or misaligned door/drawer or visible wear at the contact point

• Disconnect power to the appliance before beginning any repair
• Remove the door, drawer, or trim to access the old bumper if needed
• Slide or press the old bumper out and install the new bumper until fully seated;
• Replace any damaged clips or fasteners with OEM parts for a secure fit

This door hinge secures and pivots the refrigerator door so it opens and closes smoothly, restoring proper door alignment and seal for reliable cooling performance. What it does:

• Supports the refrigerator door and provides a smooth pivot point for opening and closing
• Helps maintain proper door alignment to ensure a tight seal and consistent internal temperature
• Can prevent or correct door sag, rubbing, or uneven gaps
• Reduces noise or sticking that occurs when the hinge is worn or damaged

• Disconnect power to the appliance before attempting repairs and work with the door supported to prevent dropping
• Use appropriate tools to remove and reinstall hinge fasteners; keep track of any washers or shims
• Verify door alignment and gasket seat after installation; adjust hinge position as needed before fully tightening
• If other hinge hardware is worn or damaged, replace those components to ensure proper function

This 10-32 x 3/8 machine screw secures appliance components. It keeps panels, brackets, and trim firmly attached so everything stays aligned and quiet during operation.

• Fastens metal parts using a 10-32 thread in pre-tapped holes or with a matching 10-32 nut
• Maintains proper alignment of panels, brackets, and trim to reduce vibration and rattling
• Replace if the original screw is missing, stripped, rusted, or damaged
• Using the correct hardware helps restore a secure, factory-tight fit

• Disconnect power; shut off gas supply if applicable. Allow the appliance to cool completely before servicing
• Note screw locations/lengths and replace like-for-like
• Start threads by hand to avoid cross-threading; snug with the appropriate driver—do not overtighten
• If the receiving threads are damaged, repair or replace the mating component before installing

Color: Stainless

This door plastic bracket secures the appliance door to the cabinet, keeping the door aligned and stable so it closes properly and seals. A simple replacement for worn, cracked, or broken door support hardware. What it does

• Holds the door in the correct position and connects the door assembly to the cabinet.
• Restores proper door alignment to reduce gaps, scraping, or uneven closing.
• Stops rattling or rocking caused by a cracked or broken bracket.
• Helps the door latch and seal correctly so the appliance can operate safely.

• One door plastic bracket (LW) as shown.

• Disconnect power (and water if applicable) before starting any repair.
• Access may require removing the door or inner door panel; keep track of fasteners.
• Inspect surrounding screws, clips, and the mating surface; replace any damaged fasteners.

This replacement door plastic bracket secures the appliance door to the cabinet hinge so the door opens and closes smoothly and stays aligned. It restores proper door support and reduces sagging or uneven gaps. What it does:

• Provides a secure mounting point between the door and hinge assembly
• Supports door weight to prevent sagging and misalignment
• Helps the door close flush to maintain an effective seal
• Reduces rattling or excessive movement during operation
• Common symptom: door feels loose, hangs unevenly, or doesn't latch properly

• One door plastic bracket

• Disconnect power (and water if applicable) before starting any repair
• Remove the door per manufacturer instructions to access the bracket; keep track of screws and any spacers
• Inspect hinge and surrounding parts for wear; replace any damaged hardware for best results
• If the part fits tightly, avoid forcing it; use appropriate tools and follow OEM torque guidelines

The Oven Door Glass Spacer is an OEM part for Whirlpool ovens. This part helps maintain the structural integrity of the oven door, preventing heat escape, and ensuring the door glass remains securely in place during the oven's operation. 

Causes of a bad Oven Door Glass Spacer can range from wear and tear over time, leading to degradation or loss of the spacer, to improper installation that may cause the spacer to dislodge or fail to provide adequate support. 

Symptoms of a malfunctioning Oven Door Glass Spacer include:

• Loose or rattling oven door glass
• Uneven gaps around the door glass, indicating misalignment
• Heat leaking from around the oven door, potentially affecting cooking performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is the heat-resistant glass panel on the cavity side of the oven door. Replacing a damaged pane restores a clear view into the oven and helps the door retain heat for consistent cooking. What it does:

• Serves as the inner door pane facing the oven cavity to contain heat
• Maintains a clear viewing window to monitor food during cooking
• Helps the door insulate properly for stable temperatures
• Replace if the glass is cracked, chipped, shattered, or missing

• One cavity glass panel

• Disconnect power at the breaker and allow the appliance to cool completely
• Remove the door and work on a padded surface; note the exact stack order of panes, gaskets, and trim
• Handle glass with cut-resistant gloves; edges can be sharp
• Do not overtighten fasteners when reassembling to avoid stressing the glass

A 27-inch replacement refrigerator door handle that restores a secure grip and fresh appearance. Designed to match factory fit and finish for a clean, usable door surface. What it does:

• Provides a sturdy handhold for opening and closing the refrigerator door
• Restores proper clearance and alignment when the original handle is cracked or broken
• Helps prevent sharp edges and reduces risk of cuts from damaged handles
• Improves the cabinet's appearance when the original handle is worn or faded

• One replacement 27-inch door handle

• Remove power to the appliance or open doors fully to prevent pinching during installation
• Use appropriate hand tools; avoid overtightening fasteners to prevent cracking
• Keep screws and small parts secure—inspect existing mounting points for damage before attaching