Parts for Thermador PRD366EG02: Oven Parts

The temperature sensor is an electronic probe that monitors internal appliance temperature and reports it to the control so it can regulate operation. Replacing a failed sensor restores more accurate temperatures and can clear temperature-related error codes. What it does:

• Senses internal temperature via resistance changes and sends the signal to the electronic control
• Helps the control reach and maintain the set temperature during operation
• Common failure symptoms: too hot/cold, won't reach set temp, long/short cycles, temperature error codes
• Can cause preheat to stall or the unit to shut off early (model dependent)

• Includes: 1 temperature sensor

• Disconnect power at the breaker before servicing
• Location and access vary by model; typically mounts with screws or a clip and connects to a 2-wire harness
• Handle the connector and wiring carefully; route and secure away from hot or moving parts
• After installation, clear stored errors and run a test cycle to proper readings

The Lamp is an OEM part for Bosch ranges and ovens. The range lamp provides visibility when viewing food through the oven window or checking on items cooking on the stove.

Causes of a bad range lamp can include normal wear and tear over time, as well as accidental damage from impact or handle mishandling.

Symptoms of a bad range lamp include:

• Diminished light that does not adequately illuminate the cooking space
• Flickering or unstable illumination
• A burned out or broken bulb

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Restore reliable baking performance with this bake heating element. Mounted at the bottom of the oven, it provides the primary heat source in Bake mode so the cavity reaches and maintains the set temperature for consistent results. What it does:

• Heats the oven in Bake mode to reach and hold the set temperature
• Failure can cause no heat in bake, very slow preheating, or uneven/undercooked results
• Visible cracks, blisters, or a broken coil indicate the element should be replaced
• A shorted element may trip a household breaker or blow a fuse

• One bake heating element

• Disconnect power at the breaker and allow the oven to cool before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wire terminals
• Transfer wires one at a time to the new element; do not allow wires to fall back into the insulation
• Reinstall the element and panels, restore power, and test bake operation

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

A cable harness that routes and connects power and signal wires to restore proper electrical continuity and control communication in your appliance. Replaces a worn or damaged harness to help eliminate intermittent power or control faults. What it does:

• Provides bundled wiring and connector interfaces between control boards, motors, sensors, and switches
• Restores reliable electrical connections when original wires or terminals are frayed, broken, or corroded
• Can resolve symptoms such as intermittent operation, loss of power to components, or control panel communication errors
• Matches OEM connector types and wire routing to maintain correct electrical function

• Disconnect all power (unplug appliance or switch off breaker) before starting service
• Note wire routing and connector positions during removal to ensure correct reinstallation
• Handle connectors by the housing; avoid pulling on individual wires

This fan cover protects the appliance's blower assembly and directs airflow to maintain proper ventilation. It helps prevent debris from reaching the fan and supports efficient air movement for reliable operation. What it does:

• Shields the blower/fan from dust, lint, and loose debris that can interfere with airflow
• Directs and channels airflow for consistent ventilation and cooling of internal components
• Helps reduce noise by enclosing the fan area and stabilizing the blower assembly
• Commonly replaced when cracked, damaged, or warped after impact or wear

• One fan cover

• Inspect surrounding seals and mounting tabs before installation; replace any broken clips
• Power off and disconnect the appliance before accessing internal components
• May require basic tools (screwdriver, socket) and removal of adjacent panels for access

This Broil Heating Element is an OEM part for Bosch Ranges. It is responsible for providing high heat for broiling functions and evenly distributing heat within the oven cavity. It ensures efficient broiling performance for cooking various dishes.

A common issue with a malfunctioning Broil Heating Element is wear and tear over time, leading to potential element damage or failure. Frequent usage, or heating irregularities can compromise its function.

Symptoms of a defective Broil Heating Element may include:

• Uneven broiling or cooking results
• Inadequate heating or failure to reach desired temperatures
• Visible damage or signs of wear on the heating element

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This bottom cavity cover replaces the removable floor panel under the oven cavity to protect internal components and help contain spills for easier clean-up. It restores the oven's lower interior surface for safe, tidy operation. What it does:

• Covers and protects the oven cavity floor and components from drips, crumbs, and direct heat exposure
• Helps keep the lower oven area clean and makes wiping up spills simpler
• Supports proper airflow path and component protection when installed
• Commonly replaced when the original cover is dented, warped, or damaged

• One bottom cavity cover

• Turn off and disconnect power to the appliance before starting any repair
• Allow the oven to cool completely; use gloves to handle sharp edges
• Installation typically requires removing the oven racks and sliding the cover into position; keep fasteners if present