Parts for Thermador PRD366EHU03: Oven Parts

The temperature sensor is an electronic probe that monitors internal appliance temperature and reports it to the control so it can regulate operation. Replacing a failed sensor restores more accurate temperatures and can clear temperature-related error codes. What it does:

• Senses internal temperature via resistance changes and sends the signal to the electronic control
• Helps the control reach and maintain the set temperature during operation
• Common failure symptoms: too hot/cold, won't reach set temp, long/short cycles, temperature error codes
• Can cause preheat to stall or the unit to shut off early (model dependent)

• Includes: 1 temperature sensor

• Disconnect power at the breaker before servicing
• Location and access vary by model; typically mounts with screws or a clip and connects to a 2-wire harness
• Handle the connector and wiring carefully; route and secure away from hot or moving parts
• After installation, clear stored errors and run a test cycle to proper readings

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

A cable harness that routes and connects power and signal wires to restore proper electrical continuity and control communication in your appliance. Replaces a worn or damaged harness to help eliminate intermittent power or control faults. What it does:

• Provides bundled wiring and connector interfaces between control boards, motors, sensors, and switches
• Restores reliable electrical connections when original wires or terminals are frayed, broken, or corroded
• Can resolve symptoms such as intermittent operation, loss of power to components, or control panel communication errors
• Matches OEM connector types and wire routing to maintain correct electrical function

• Disconnect all power (unplug appliance or switch off breaker) before starting service
• Note wire routing and connector positions during removal to ensure correct reinstallation
• Handle connectors by the housing; avoid pulling on individual wires

This fan cover protects the appliance's blower assembly and directs airflow to maintain proper ventilation. It helps prevent debris from reaching the fan and supports efficient air movement for reliable operation. What it does:

• Shields the blower/fan from dust, lint, and loose debris that can interfere with airflow
• Directs and channels airflow for consistent ventilation and cooling of internal components
• Helps reduce noise by enclosing the fan area and stabilizing the blower assembly
• Commonly replaced when cracked, damaged, or warped after impact or wear

• One fan cover

• Inspect surrounding seals and mounting tabs before installation; replace any broken clips
• Power off and disconnect the appliance before accessing internal components
• May require basic tools (screwdriver, socket) and removal of adjacent panels for access

This heating element warms wash water and helps dry dishes by raising dishwasher tub temperature for improved cleaning and drying results. Replaces a failed or damaged tub heater to restore normal wash-cycle heating. What it does:

• Heats dishwasher wash and rinse water so detergents activate and soils break down
• Speeds or improves drying performance by raising internal temperature during final cycles
• Commonly replaced when dishwasher shows no heat, poor cleaning, or poor drying
• Works with dishwasher controls and sensors to cycle heat during selected programs

• Disconnect power and water supply before starting work to avoid shock or flooding
• Drain the dishwasher and remove the lower access panel to reach the element assembly
• Handle the element and wiring gently; replace any damaged seals or grommets to prevent leaks
• Test operation and check for leaks after reinstalling panels and restoring power

This heating element warms dishwasher wash and rinse water for better cleaning and helps dry dishes more effectively. It replaces a failed or damaged heater to restore normal wash temperatures and drying performance. What it does:

• Heats wash and rinse water so detergent activates and soils loosen
• Supports the dishwasher's drying cycle by raising internal temperature
• Commonly linked to symptoms like dishes not drying, water not heating, or wash cycles running longer
• Works as the in-tub heater assembly that the controller energizes during cycles

• Disconnect power and water supply before attempting any service
• Access may require removing the dishwasher toe kick or interior panels
• Handle with care to avoid damaging terminals or tank fittings; replace any worn seals