Parts for Lg LP090CEM: Package Unit Parts

A box-style film capacitor used in appliance control and motor circuits to stabilize voltage and filter electrical noise. Replaces a worn or damaged capacitor to help restore reliable operation and reduce electrical interference. What it does:

• Smooths and filters voltage peaks to protect controls and electronics
• Helps reduce electrical noise that can cause erratic motor or control behavior
• Supports stable operation of motors and control boards in the circuit
• Commonly replaced when capacitor is cracked, bulging, or electrically failed

• Disconnect power to the appliance before servicing to avoid shock hazard
• Discharge the capacitor before handling; capacitors can hold a charge after power is removed
• Match polarity and terminal layout to the original part; install only in the intended circuit location

This clamp secures a line or connection inside your appliance, maintaining a tight fit under vibration. Replacing a fatigued clamp helps prevent leaks or disconnections and keeps components anchored so the system operates reliably.

• Holds a line/fitting firmly to keep the joint sealed and secure
• Helps prevent leaks or disconnections at hose/tube connections
• Resists vibration that can loosen fittings during operation
• Replace if bent, weakened, or corroded, or if the connection repeatedly loosens

• Disconnect power and, if applicable, shut off water supply before service
• Note clamp orientation and routing; seat the clamp just behind the fitting bead/stop
• Use the correct tool for your clamp style to compress or tighten evenly
• After reassembly, restore utilities and test for leaks or movement

A single replacement barrier that holds and separates items inside the appliance, restoring proper organization and preventing shifting or contact. Fits in the OEM mounting location and replaces a cracked, broken, or missing barrier. What it does

• Replaces a damaged or missing internal barrier that secures items and keeps them from shifting.
• Restores the intended spacing and containment inside the compartment or door pocket.
• Reduces rattling and contact-related damage to stored items.
• Helps maintain proper storage layout and ease of use.

• Install with the OEM mounting tabs or screws; verify correct orientation before securing.
• Use basic hand tools; do not force the part into place to avoid breaking tabs.
• Unplug the appliance before working.
• Inspect adjacent mounting clips or shelves and replace if worn to ensure a secure fit.

This supporter is a replacement support bracket that helps hold and steady internal components for proper alignment and operation. It restores secure mounting and reduces movement that can cause noise or wear. What it does:

• Secures internal assemblies to the cabinet so parts stay aligned during use
• Helps prevent excess vibration and noise caused by loose or worn supports
• Can resolve symptoms like rattling, knocking, uneven operation or parts shifting
• Replaces a damaged or broken bracket to restore proper fit and clearance

• One supporter support bracket

• Disconnect power and unplug the appliance before starting any repair
• Access may require removing exterior panels or covers;
• Keep track of mounting hardware; reuse original screws if not supplied

This replacement air filter helps reduce common refrigerator odors and maintain fresher-smelling interior air. It installs in the dedicated filter compartment to help keep stored food smelling neutral and reduce lingering smells. What it does

• Absorbs and neutralizes food and cooking odors inside the refrigerator
• Helps reduce stale or sour smells that can develop over time
• Supports overall freshness of stored food by filtering internal air
• Common symptom: persistent or recurring refrigerator odors despite cleaning

• One air filter designed for the refrigerator's filter compartment

• Locate the filter compartment per your owner's manual and remove the old filter before installing the new one
• Install new filter until it seats securely; follow any filter-reset steps if your model requires them
• Dispose of used filter following local regulations
• If odors persist after replacement, check for spoiled food, spills, or blocked vents

This air filter screens dust and lint at the intake to protect internal components and keep airflow steady. Replacing a clogged or damaged filter helps maintain performance and reduces strain on the system.

• Traps dust and lint before they reach the evaporator and blower
• Helps maintain proper airflow and overall cooling performance
• Reduces debris buildup on coils and helps protect the fan
• Common signs of a dirty or damaged filter: weak airflow, reduced cooling, longer run times, visible dirt or tears

• Disconnect power to the appliance before servicing
• Access the filter per your model's instructions; many units slide it out from behind the front grille
• Install the new filter in the same orientation; ensure it sits flat and fully seated
• Do not operate the unit without the filter in place

This NTC thermistor assembly is the temperature-sensing probe and harness the control uses to read actual temperatures and regulate operation. Replacing a failed sensor restores accurate temperature feedback for consistent performance and proper cycling. What it does:

• Senses temperature via a negative temperature coefficient element; resistance decreases as temperature rises
• Sends the signal to the control board to manage operation and cycle timing as designed
• Typical symptoms include inaccurate temperatures, not maintaining set temperature, extended run times or short cycling, and sensor-related error codes
• Often reads out of range when tested at known temperatures

• One NTC thermistor assembly

• Disconnect power to the appliance before servicing; turn off water supply if applicable
• Note original sensor placement, routing, clips, and insulation before removal
• Install the new assembly; route wiring away from sharp edges, heat, and moving parts; secure any clips/insulation as found
• Restore power and run a diagnostic or allow the unit to stabilize, then verify operation

This power cord assembly supplies mains power to your appliance and replaces a worn, damaged, or broken cord to restore reliable electrical connection. Designed to match the original cord form and plugged connection for a direct replacement. What it does

• Delivers AC power from the wall outlet to the appliance's inlet.
• Replaces frayed, cut, or heat-damaged cord that can cause intermittent power or no power.
• Restores a secure plug connection when the plug or wiring is loose or exposed.
• Helps prevent arcing and unsafe connections when the original cord is compromised.

• One power cord assembly.

• Always unplug the appliance or shut off power at the breaker before installing.
• Installation is typically a direct swap; route the cord and secure strain relief as original.
• Verify the cord's connector seats fully and that wiring matches the appliance inlet polarity.

The Blower Wheel Bearing is an OEM part for LG air conditioners. This bearing supports the blower wheel, ensuring smooth rotation and efficient airflow throughout the unit. 

Causes of a bad blower wheel bearing can include wear and tear from regular use, lack of lubrication, or damage from debris or impact. 

Symptoms of a bad blower wheel bearing include:

• Unusual grinding or squealing noises from the blower area
• Reduced airflow or diminished cooling efficiency
• The blower wheel wobbling or vibrating excessively
• The fan motor struggling to start or run smoothly

This OEM LG part is also compatible with some Kenmore models.

New bracket is also required. Part # 4960A20032A.

This isolator routes microwave energy between the magnetron and waveguide to help protect components and maintain consistent heating performance. Replacing a failed isolator can restore reliable cooking and help prevent further high-voltage damage. What it does:

• Directs RF energy from the magnetron into the waveguide/cavity
• Helps protect the magnetron by reducing reflected energy
• Aids in preventing arcing or burn damage in the waveguide area
• Common symptoms of failure: no heat or uneven heating, loud humming/buzzing, visible arcing/burn marks near the waveguide

• 1 isolator

• Disconnect power and discharge the high-voltage capacitor before servicing; risk of electric shock
• Handle waveguide components carefully; avoid contaminating RF surfaces and note exact orientation
• Take photos of the original setup to match positioning and fastener locations

The A/C Condenser Fan Blade is an OEM part for LG air conditioners. This fan blade is responsible for drawing air through the condenser coils to dissipate heat, ensuring the air conditioner operates efficiently and effectively.

Over time, the condenser fan blade can become damaged or worn out due to exposure to outdoor elements, debris, or physical impact. Additionally, regular use can lead to wear and tear, affecting the fan blade’s performance.

Symptoms of a bad A/C condenser fan blade include:

• Reduced cooling efficiency
• Unusual noises such as rattling or clanking from the fan area
• The fan not spinning or spinning unevenly
• The air conditioner frequently cycling on and off due to overheating

This OEM LG part is also compatible with Sears/Kenmore models.