Parts for Whirlpool TU800SPPB0: 03 - Panel And Control Parts

Size: 8 x 1/2 ab.

This Knob-Switch is a direct-fit control knob that lets you select settings and actuate the appliance's switch function for user control. It restores reliable manual control when the original knob is worn, cracked, or no longer engages. What it does:

• Rotates and/or presses to change the appliance setting while activating the internal switch mechanism
• Restores tactile control and proper engagement if the original knob is stripped, cracked, or loose
• Helps eliminate intermittent or non-responsive controls caused by a damaged knob interface
• Matches OEM fit and control ergonomics for accurate selection and operation

• One Knob-Switch

• Disconnect power to the appliance before servicing to avoid shock or injury
• Typically pulls straight off the control shaft; inspect the shaft and switch for wear before installing
• If the knob does not seat correctly after replacement, verify shaft style (splined vs. round) and switch retention

This rotary switch knob restores easy, reliable control of the appliance's front-panel settings. It replaces a cracked, missing, or worn control knob so selections turn smoothly and are easy to adjust. What it does:

• Fits onto the control's rotary switch shaft to allow selection of cycles and settings.
• Replaces a loose, cracked, stripped, or missing knob that is hard to turn or won't stay in position.
• Matches the original black finish for a consistent appearance on the control panel.
• Secures to the existing splined shaft (or set-screw where applicable) for a direct replacement.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the old knob by pulling it straight off the control shaft; align splines and push the new knob onto the shaft until fully seated.
• If the knob uses a set screw, tighten it securely but do not overtighten.

Color: Black.

Color: Black

The On/Off Rotary Switch Kit is an OEM part for Whirlpool trash compactors. This kit includes the rotary switch and necessary components to control the power and operation of the trash compactor, allowing users to turn the unit on and off easily.

Causes of a bad rotary switch can include electrical wear and tear, damage from repeated use, or issues with the internal contacts. Over time, these factors can lead to the switch becoming unresponsive or failing to control the compactor properly.

Symptoms of a bad rotary switch include:

• The trash compactor not turning on or off
• Intermittent operation of the compactor
• The switch feeling loose or unresponsive
• Electrical sparking or unusual noises from the switch area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 6-20 x 1.0 inch.

This retainer bracket secures internal components in place to restore proper alignment and support. It replaces a worn or broken bracket to help reduce rattling, misalignment, or loose parts during operation. What it does:

• Holds and supports internal assembly parts to maintain correct positioning
• Prevents movement that can cause noise, vibration, or rubbing
• Restores stability after bracket damage or wear
• Works as a direct-fit replacement when the original bracket is broken or bent

• High-level replacement — basic hand tools required;
• Disconnect power (and gas if applicable) before beginning any repair
• Inspect surrounding parts and hardware; replace any damaged fasteners for a secure fit

This switch nut secures a rotary control or switch to the appliance's front panel. Replacing a stripped or missing nut keeps the control stable so the knob turns smoothly and the shaft stays properly aligned.

• Clamps the switch/control to the panel to prevent movement or rotation
• Helps maintain correct knob alignment with dial markings
• Common symptoms: loose or wobbly knob, switch rotates in the panel, missing/damaged nut
• Often needed after service if the original nut is stripped or lost

• Disconnect electrical power before servicing
• Remove the knob and any decorative escutcheon; thread the new nut onto the switch bushing from the front of the panel
• Support the switch from behind while tightening; do not overtighten to avoid panel or switch damage
• Restore power and test control operation