Kenmore Range Hood 233.10442 (23310442, 233 10442) Parts

The Light Socket is an OEM replacement part for Broan range hoods. This electrical fitting provides a power connection point for light fixtures above stovetops. A faulty socket jeopardizes safe operation.

Causes of a bad socket can include loose wire connections allowing arcing or shorts, moisture intrusion corroding terminals, or cracking of plastic insulation. 

Symptoms of a bad light socket include: 

• Intermittent or non-functioning lights  
• Warm socket housing or abnormal smells/sounds
• Tripped breakers or blown fuses servicing the range hood

This OEM component fits additional brands like Thermador, Viking, and some Kenmore range hood models using equivalent Broan designs.

Secures the grease filter in your Allure range hood. This filter spring kit replaces worn or missing springs so the filter stays seated, reducing rattling and preventing the filter from dropping during operation.

• Applies spring tension to hold the grease filter in place
• Helps maintain proper airflow by keeping the filter fully seated
• Reduces vibration and noise from a loose filter
• Common symptoms: filter falls out, hangs loosely, or is hard to keep latched

• Disconnect power at the breaker before servicing the hood
• Remove the grease filter(s) to access the spring location
• Wear cut-resistant gloves; sheet metal edges can be sharp
• Ensure springs are fully seated in the factory slots/tabs, then test-fit the filter

This factory replacement plate provides a rigid, stable mounting surface inside your unit. Replacing a bent or damaged plate helps keep internal components securely positioned and operating smoothly.

• Supports and locates attached components for correct fit and function
• Helps maintain alignment to reduce rubbing, vibration, or rattling noises
• Restores secure mounting when the original plate is bent, cracked, or missing
• Direct-fit replacement built to match the original footprint

• Disconnect power at the breaker before servicing
• Wear cut-resistant gloves; metal edges can be sharp
• Support attached parts and transfer any brackets or hardware from the old plate
• Tighten fasteners evenly before restoring power

A small replacement mounting screw used to secure range hood and ventilation components. Restores loose or missing fasteners so panels and assemblies sit firmly and stop rattling or shifting during use. What it does

• Secures trim, grille, brackets or other small assemblies to the main housing
• Replaces a missing or stripped screw that causes rattling or loose parts
• Helps restore proper alignment of removable panels and covers
• Works as a direct fastener when the original screw is lost or damaged

• Turn power off to the appliance before working on vents or housings
• Use the matching screw hole and do not force a different-size fastener
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• If threads are damaged, replace the mating clip or insert before using this screw

This isolation transformer supplies the low-voltage control circuit that powers switches, relays and controls in the ventilation unit—restoring proper control operation and stable low-voltage output. What it does:

• Converts and isolates the appliance control circuit from main power to protect controls and reduce electrical noise
• Restores low-voltage power to switches, relays and electronic controls that fail when the transformer is bad
• Prevents intermittent or no-response symptoms from control panels and blower/light circuits
• Provides a direct replacement for the original transformer to maintain proper control operation

• Disconnect all power to the appliance before starting any work
• Verify wiring locations and terminal markings; match connections exactly to the original transformer
• Inspect mounting and harness routing; secure transformer to prevent vibration

This replacement control panel restores the front appearance and user interface on compatible Broan range hood units. It provides a clean surface and mounting area for switches and control hardware to help the hood operate as intended. What it does:

• Replaces cracked, dented, or scratched front panel surfaces that affect appearance
• Provides the mounting surface and openings for switches, knobs, and indicator lights
• Protects internal control components from grease and debris
• Common symptoms it addresses: broken or missing panel, exposed wiring, or buttons that no longer sit flush

• Disconnect power to the appliance before starting any work
• Typical installation requires basic hand tools (screwdriver); keep fasteners for reuse or replace if damaged