Kenmore Range Hood 233.5237810 (2335237810, 233 5237810) Parts

This replacement knob restores a clean look and reliable control of your unit's settings. It fits onto the control shaft to give you a secure, easy-to-grip dial when the original knob is cracked, loose, or missing.

• Press-fits onto a control shaft to operate the switch or speed control
• Provides a secure grip for selecting settings as intended
• Replaces damaged, cracked, or missing knobs
• Helps address slipping, free-spinning, or hard-to-turn controls

• Disconnect power to the appliance before servicing
• Pull the old knob straight off; avoid prying against the panel to prevent damage
• Align the flat/D-shaped insert with the shaft and press on until fully seated
• Restore power and test operation

This replacement fan motor drives the blower that moves air through your ventilation system. Replace a failing motor to help restore proper airflow and reduce noise during operation. What it does:

• Spins the blower wheel/impeller to move air through the venting system
• Helps clear steam, smoke, and odors by maintaining consistent airflow
• Can address symptoms like a fan that won't start, just hums, runs slowly, or is unusually noisy
• Resolve overheating or a burning smell coming from the motor area

• 1 motor

• Disconnect power at the breaker before servicing
• Note wire locations and motor orientation for correct reassembly
• Ensure the blower wheel is secure and spins freely after installation
• Test run before final reassembly and check for vibration or rubbing

This electronic control module operates the hood's fan and lights so the range hood responds to user commands and runs reliably. Replaces a failed or unresponsive control to restore normal vent and lighting operation. What it does:

• Receives input from the hood's buttons or touchpad and activates fan speeds and lights
• Controls power to blower motor and lighting circuits based on user selections
• Can resolve symptoms like unresponsive controls, intermittent fan/lights, or loss of specific speed settings
• Works as the main interface between user controls and the hood's electrical components

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle the module carefully; avoid bending pins or exposing it to static
• Typical install requires removing the hood's access panel and unplugging the old module connector(s)
• Test all functions after installation and secure panels before returning the hood to service

Includes two filters

A replacement rocker-style switch that restores on/off control for range hood lights or fans, helping fix loss of power or intermittent operation. Simple direct-fit design for easy swap-out and reliable everyday use. What it does

• Provides on/off control for hood lights or blower motors where the original rocker switch failed
• Replaces a worn, stuck, or non-responsive rocker to restore consistent power
• Commonly used when lights won't turn on, fan won't start, or operation is intermittent
• Handles user input with a tactile rocker action for straightforward operation

• One rocker-style switch

• Disconnect power to the appliance at the breaker before servicing
• Remove the hood/light housing per the appliance service instructions to access the switch
• Note wire locations or take a photo before disconnecting leads to ensure correct reconnection

This is a replacement mounting nut used to secure components and hardware in range hoods and ventilation assemblies. It provides a simple, reliable fastener to hold studs, bolts, or threaded posts in place. What it does:

• Secures panels, mounting brackets, or trim pieces to threaded studs or bolts
• Helps keep components aligned and prevents parts from slipping loose
• Can be used where a small, standard nut is required for assembly or repair
• Commonly replaced when stripped, corroded, or missing to restore safe attachment

• Disconnect power to the appliance and ensure the area is safe before servicing
• Match nut to the correct stud/bolt thread size and pitch before installation
• Tighten with the appropriately sized wrench; avoid over-tightening which can strip threads
• Replace any damaged mating hardware for a secure fit

This hex mounting nut secures components and fasteners on compatible Broan range/ventilation assemblies, restoring proper fit and preventing looseness. It's a small but essential fastener for stable operation and quiet performance. What it does:

• Secures fan, grille, or housing fasteners to prevent parts from working loose
• Helps stop rattling or vibration caused by loose hardware
• Maintains alignment of mounted components for reliable operation
• Works with matching machine screws or studs where a hex nut is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct-size wrench or socket to avoid rounding the nut
• Tighten snugly but avoid over-torquing to prevent thread or part damage
• Replace any damaged mating fasteners or hardware for a lasting repair