Kenmore Air Conditioner 253.70085010 (25370085010, 253 70085010) Parts

Screens air and captures odors and particles in your room air conditioner. Replace when clogged to maintain proper airflow. Confirm fit with your model.

Filter drier removes moisture and contaminants from your air conditioner's refrigerant system. Replace when cooling performance drops or after repairs. Verify fit with your model number.

This blower wheel circulates air through the dryer drum and venting system to maintain proper airflow for efficient drying. Replaces a worn or damaged wheel to help restore drying performance and reduce unusual noises. What it does:

• Channels air from the dryer motor through the drum and exhaust system
• Helps maintain consistent drum airflow for faster, more even drying
• Can reduce or stop rattling, scraping, or thumping noises caused by a broken or imbalanced wheel
• Restores proper vent pressure that can prevent extended dry cycles

• Disconnect power to the appliance before beginning any repair.
• Access usually requires removing the dryer front or rear panel; keep fasteners organized.
• Inspect the motor shaft, mounting clip, and housing for wear; replace damaged hardware as needed.

Replacement louver for room air conditioners. Directs airflow and completes front panel appearance. Order now if yours is cracked, broken, or missing.

Front grille for room air conditioners. Covers the internal components and provides air intake. Replace if cracked, broken, or discolored from sun exposure.

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded

Support rod for room air conditioners. Installs in the chassis to provide structural reinforcement. Replace if bent, broken, or missing during unit assembly.

Fix weak airflow or loud operation in your air conditioner with this fan blade. Common repair for units that run but don't cool effectively.

Seal for air conditioners prevents air leaks and maintains cooling efficiency. Replace if worn, cracked, or causing energy loss. Verify fit with model number.

Assorted screws and clips for securing air conditioner panels and components. Replace missing, stripped, or damaged mounting hardware to restore fit.

Seal and spacer kit for air conditioners. Replace when you notice air leaks, reduced cooling efficiency, or during unit maintenance. Verify fit with your model number before ordering.

If your air conditioner won't start or runs but doesn't cool properly, the capacitor may have failed. This part stores electrical energy to start the compressor.

Control panel for room air conditioners. Fixes unresponsive buttons, display issues, or mode selection problems. Moderate DIY repair in 30-45 minutes.

Fix an air conditioner that won't start, won't cool, or has erratic operation with this control box. Contains essential electronics and relays.

This lower front toe-kick grille replaces a damaged or missing lower front panel to restore the refrigerator's finished appearance and protect the venting area. It fits into the toe-kick opening and provides a clean, finished look. What it does

• Covers the refrigerator's lower front vent/condensing area for a finished appearance
• Helps keep debris and small objects out of the vent opening
• Replaces cracked, warped, or missing toe-kick panels that detract from the appliance's look
• Restores proper panel alignment and cosmetic appearance after damage

• Disconnect power or unplug the appliance before working near electrical components.
• Many installations use snap-in tabs or a few fasteners; remove the old grille and align tabs, then press or secure per the service manual.
• Use basic hand tools and follow the model-specific service instructions for safe removal and reinstallation.