Lg Microwave 2263672 Parts

Microwave won't heat but runs normally? A failed magnetron is the likely cause. This part generates the microwaves that cook food. Moderate DIY repair.

This is a micro switch that detects whether the microwave door is properly closed and latched. It is part of the safety interlock system that prevents the microwave from operating with the door open. Replace this switch if the microwave does not start when the door is shut, runs with the door open, blows a fuse when the door closes, or stops mid-cycle intermittently.

Replaces a cracked, chipped, or broken glass turntable tray inside your microwave cavity. Typically damaged during cleaning or accidental impacts.

The Switch, Micro is an OEM part for LG microwaves. This micro switch is crucial for the operation of the microwave door mechanism, ensuring that the microwave only operates when the door is securely closed.

Causes of a bad micro switch can include wear and tear from frequent use, damage due to electrical faults, or physical impact that disrupts its functionality.

Symptoms of a bad micro switch include:

• The microwave not starting or stopping unexpectedly
• The door not latching properly
• The microwave light not turning on or off correctly
• Error messages appearing on the control panel

This OEM LG part is also compatible with Sears/Kenmore models.

Replace your microwave's halogen bulb to restore interior and cooktop lighting. Recommended when bulb burns out from normal use. Verify fit by model number.

This thermostat is a temperature-sensitive safety switch used in LG microwaves. It monitors internal temperature and opens the circuit when overheating is detected to help protect components from heat damage.

• Monitors temperature at its mounting location inside the microwave
• Opens on overtemperature to interrupt power for safety
• Depending on model/location, a failed or open thermostat can cause no heat, the unit shutting off mid-cycle, or no power until it cools
• Helps prevent damage to the magnetron, cavity, and wiring due to overheating

• Unplug the microwave before service; the high-voltage capacitor can retain a dangerous charge
• Note wire positions, remove mounting screws, and install the new thermostat flat against the surface for proper heat sensing
• Reassemble and test; ensure vents and filters are clear to maintain proper airflow and prevent future overheating

Threaded nut assembly secures internal components in your microwave. Replace if stripped, worn, or missing to eliminate rattling and maintain alignment.

Truss head tapping screw secures panels, brackets, and covers in appliances. Replaces missing or damaged fasteners to restore snug fit and alignment.

Thermistor is a temperature-sensing replacement that monitors refrigerator and freezer temperatures so the control board can regulate cooling. Replacing a faulty thermistor restores accurate temperature readings and helps stabilize cooling performance. What it does:

• Senses interior/evaporator temperature and sends a signal to the control board for temperature regulation.
• Helps prevent erratic cooling, long run-times, or inconsistent compartment temperatures when operating correctly.
• Faulty thermistors can contribute to excessive frost, failed defrost cycles, or compressor cycling issues.
• Use when the existing sensor fails to report correct temperatures or the part number matches.

• Always disconnect power to the appliance before servicing to avoid shock or damage.
• The sensor is typically mounted on or near the evaporator or inside a cabinet wall; access may require removing panels or covers.
• Handle the sensor and wiring harness gently; avoid pulling on wires or bending the sensor element.

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

Fix a microwave turntable that won't spin or wobbles during heating. This replacement shaft restores smooth glass tray rotation for even cooking.