Lg Dishwasher DV288HNT Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

A fixed electrical capacitor that stores and releases charge to support motor/compressor start and steady operation. Replaces a worn capacitor to restore reliable starting and reduce motor strain. What it does

• Provides the stored electrical charge needed for motor or compressor startup and smooth running
• Helps prevent weak starts, extended spin-up, or failure to start
• Can stop buzzing or humming associated with a failing start circuit
• Can reduce intermittent operation or frequent circuit trips caused by a bad capacitor

• Disconnect power to the appliance before servicing to avoid shock
• Discharge the capacitor before handling; use insulated tools or a resistor per service manual guidance
• Verify replacement matches your appliance's service literature or parts diagram before installing

This electrolytic capacitor helps stabilize and filter DC power on appliance control boards so electronics run reliably and noise is reduced. Replace a failing cap to restore consistent control operation and prevent erratic behavior. What it does:

• Smooths and filters DC voltage to protect control electronics from spikes and noise
• Helps maintain steady power to motors, relays, and sensors for reliable operation
• Failing caps can cause intermittent operation, error codes, non-starts, or unusual noises
• Commonly used on control boards and power supply circuits in appliances

• Always unplug the appliance and discharge capacitors before touching electronic components
• Observe correct polarity when installing; electrolytic capacitors are polarized
• Inspect surrounding board and connections for heat damage or corrosion before replacement

This fixed ceramic capacitor helps stabilize and filter electrical signals on the appliance's control circuitry, restoring reliable electronic operation and reducing intermittent faults. What it does

• Smooths voltage spikes and noise on control boards to help prevent erratic behavior.
• Supports proper timing and signal filtering for electronic controls.
• Common symptom: appliance won't start or cycles erratically when the capacitor fails.
• Common symptom: control board errors, unresponsive touch controls, or intermittent operation.

• Disconnect power to the appliance before attempting any repair.
• Discharge capacitors and avoid shorting terminals; use insulated tools.
• Handle the part by its body; avoid bending or stressing leads.

A replacement diode rectifier (bridge) that restores proper AC-to-DC conversion for an appliance's electronic control circuits, helping the unit power up and operate reliably when the original diode has failed. What it does:

• Converts incoming AC into DC for control boards and inverter circuits.
• Prevents reverse current that can damage sensitive electronics.
• Common symptom: appliance won't power on or control board shows error codes.
• Works as a direct replacement for a failed or shorted diode assembly.

• Always unplug the appliance and disconnect power before starting repairs.
• Discharge capacitors on power/inverter boards before handling the diode.
• Observe correct polarity and orientation when installing the replacement.

This Schottky diode is a small board-mounted rectifier that protects and directs current in the appliance's control circuitry. Replacing a failed diode restores proper power flow and helps prevent damage to electronic components. What it does

• Directs current and prevents reverse flow that can damage control electronics
• Helps the control board convert and regulate voltage for sensitive circuits
• Commonly linked to symptoms like intermittent power, control errors, or failure to start
• Often checked when a control board shows visible burn marks or other component failures

• One Schottky diode

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock
• This is a small electronic component; remove the control board to access the diode
• Handle the board and diode with care to avoid static damage and preserve connectors

This diode rectifier is the single-direction power diode assembly used in the appliance's high-voltage/power-supply circuit to convert AC to DC and protect downstream electronics. It restores proper power flow for the control system. What it does:

• Converts alternating current from the main supply into direct current used by control electronics.
• Prevents reverse current that can damage sensitive components.
• Commonly linked to symptoms such as a blank display, control board not powering up, blown fuses, or erratic electronic behavior.
• Works as part of the appliance's power supply/rectifier stage and helps stabilize voltage to the control module.

• One diode rectifier as shown.

• Unplug the appliance and disconnect power at the breaker before servicing.
• Discharge any high-voltage capacitors and take ESD precautions when handling electronics.
• Installation typically requires access to the control/power assembly; keep track of wire locations and fasteners.

This diode rectifier assembly converts alternating current to direct current for appliance control circuits, restoring proper DC supply to components that need steady power. Replaces a failed rectifier to help recover normal electrical operation. What it does

• Converts AC to DC so electronic controls and motors receive stable power.
• Prevents reversed current flow that can damage sensitive components.
• Common symptom: control board or display loses power or behaves intermittently.
• Common symptom: compressor, fan or motor fails to start despite power present.
• Works as the electrical bridge between incoming supply and DC-powered modules.

• Disconnect all power before servicing to avoid shock or component damage.
• Inspect connectors and wiring for heat damage; replace damaged wiring as needed.
• Ensure correct orientation and secure mounting; loose connections can cause arcing.

This diode rectifier converts AC to DC for the appliance's control and power circuits, restoring proper electrical flow so electronic components and motors receive stable DC voltage. Replaces a failed or shorted rectifier to help recover normal operation. What it does:

• Converts alternating current (AC) to direct current (DC) for control boards and DC-powered components
• Prevents reverse current that can damage sensitive electronics
• Common symptom: appliance won't power on or control board behaves intermittently
• Common symptom: blowing fuses or tripped breakers that can indicate a shorted diode

• Disconnect power at the breaker or unplug the appliance before starting work
• Observe electrostatic discharge (ESD) precautions and handle circuit boards carefully
• Verify the part is the correct replacement by comparing part numbers and physical connectors

This rectifier diode replaces a failed diode that converts alternating current to direct current for electronic controls and motors. Restores proper DC supply so sensors and control boards receive stable power. What it does:

• Converts AC to DC to support control electronics and motor circuits
• Helps prevent voltage spikes from reaching sensitive components
• Commonly replaces failed, shorted, or open diodes that cause power or control faults
• Can resolve symptoms like no power to control board, erratic operation, or certain motor failures

• One rectifier diode

• Disconnect all power before servicing to avoid electric shock
• Handle with ESD precautions; avoid touching leads and board traces
• Confirm orientation/polarity and solder or connector type matches the original

This Zener diode protects and stabilizes voltage on appliance control circuits to help prevent damage from voltage spikes and ensure reliable board operation. Replace a failed diode to restore proper regulation in affected circuitry. What it does:

• Regulates voltage on the control board to protect sensitive components from surges.
• Helps prevent erratic electronics behavior caused by over-voltage or transient spikes.
• Common symptom: control board not powering correctly or intermittent electronic failures.
• Common symptom: appliances that behave unpredictably after a power event.

• High-level soldering skill required; component is typically mounted to a PCB—do not force or pry.
• Disconnect power and discharge capacitors before working on the appliance to avoid shock.
• Observe ESD precautions to protect electronic components during handling.

This Zener diode is an electronic voltage-regulation diode used on control boards to protect circuits and stabilize voltages. It replaces a failed diode to help restore proper board operation and prevent damage from voltage spikes. What it does:

• Clamps and stabilizes voltage at a specific setpoint to protect sensitive components
• Protects control electronics from transient voltage spikes and surges
• Helps prevent erratic behavior caused by unstable supply voltages
• Commonly replaced when boards fail to power up or show intermittent faults due to voltage issues

• One Zener diode as shown

• Designed for board-level replacement; handle boards carefully to avoid static damage
• Disconnect power and fully discharge capacitors before attempting repair
• If soldering is required, use proper soldering tools and techniques to avoid heat damage