Lg Dryer RC9011D Parts

This safety interlock assembly secures the washer door and signals the control when it's safe to run a cycle. Replacing a faulty unit helps restore proper locking and start functions to prevent interruptions and error codes.

• Locks the washer door and confirms it is closed to allow the cycle to start
• Sends door-closed/locked status to the control throughout the cycle
• Helps prevent the door from opening during spin or when water is present
• Common symptoms: won't start, won't lock/unlock, door error (dE) messages, cycle stops mid-wash

• Disconnect power before servicing; wear cut-resistant gloves
• Access the lock at the door opening; remove the mounting screws and disconnect the harness
• Transfer connectors to the new assembly, align, and secure without overtightening
• Ensure the door strike aligns smoothly with the new lock before testing

The Door Strike is an OEM part for LG dryers. This part engages with the door catch to keep the dryer door securely closed during operation. The door strike is essential for ensuring the door remains tightly shut, allowing the dryer to function efficiently and safely.

Causes of a bad door strike can include wear and tear from regular use, damage from slamming the door, or misalignment issues that prevent it from engaging properly with the door catch. 

Symptoms of a bad door strike include:

• The dryer door not staying closed
• The dryer not starting due to the door not being securely latched
• Difficulty in latching the door
• Visible damage or wear on the strike

This OEM LG part is also compatible with Sears/Kenmore.

This NTC thermistor is the dryer's temperature sensor. It monitors exhaust air temperature and signals the control to cycle the heat, restoring accurate drying performance and helping prevent overheating, underheating, and inconsistent results.

• Monitors exhaust air temperature by changing resistance as heat rises (NTC behavior)
• Sends temperature feedback to the control to regulate the heater or gas valve
• Failure can cause no heat, overheating, or erratic temperatures
• May lead to long dry times, short cycles, or temperature-related error codes

• Disconnect power and, for gas models, shut off the gas supply before servicing
• Access the sensor on the blower housing or exhaust duct; location varies by model
• Note wire routing; unplug the harness connector; remove the mounting fastener/clip; install the new sensor fully seated and reconnect
• Reassemble, restore power, and run a test cycle; check and clean venting to ensure proper airflow

Catches lint and fibers during each drying cycle. Replace when torn or warped to maintain airflow and drying efficiency. Verify fit with your model.

Dryer not heating or overheating? This thermostat assembly regulates temperature to prevent damage and maintain consistent drying. Easy DIY repair.

The Drain Pump Assembly is an OEM part for LG dryers. The drain pump is responsible for pumping water out of the dryer drum.

Causes of a bad drain pump can include clogging or blockage from lint buildup, damage to pump components from excessive moisture or corrosion over time, or worn out motor that has exceeded its lifespan.

Symptoms of a bad drain pump include:

• Wet clothes at the end of the cycle
• Excess moisture inside the dryer drum
• Standing water at the bottom of the dryer
• Strange noises or vibration coming from the pump area

This LG part is also compatible with some Kenmore models.

Dryer stops mid-cycle or won't start? This door latch assembly secures the door to keep your dryer running. Simple 2-minute DIY fix for most models.

Is your dryer taking too long or not drying clothes completely? A damaged blower wheel disrupts airflow circulation. Moderate DIY repair restores performance.

Dryer won't tumble or drum doesn't turn? This drum motor assembly restores rotation for even drying. Direct drive replacement part for your dryer.

Fixes weak airflow and longer dry times in your dryer. This blower impeller restores proper air movement through the ventilation system. Easy repair part.

Fix a dryer that won't tumble or makes squealing noises. This drum belt connects the motor to the drum, restoring rotation. Moderate DIY repair.

Clothes not drying or taking multiple cycles? This dryer heater assembly restores heat output. Moderate DIY repair fixes most no-heat issues quickly.

This adjustable leg assembly raises and levels the appliance to keep it stable and reduce rocking. It provides a simple way to set appliance height for proper door alignment and smooth operation. What it does:

• Supports the appliance and transfers weight to the floor
• Allows height adjustment to level uneven floors
• Helps prevent excessive vibration, rocking, and noise
• Promotes proper door/drawer alignment and seal

• One leg assembly

• Disconnect power and empty the appliance before adjusting or replacing legs
• Raise or support the appliance safely before removing or installing the leg
• Adjust by turning the leg; tighten securely but avoid over-torquing

Multi-wire harness assembly for dryers. Connects electrical components throughout the unit. Replace if wires are frayed, connections are loose, or harness is damaged.

Dryer drum glide slider that supports the front of the drum during rotation. Replace if cracked, worn, or causing noise from drum misalignment.