Bosch Refrigerator B30BB830SS Parts

Fixes unresponsive controls, display errors, or cycle failures in refrigerators and freezers. Direct replacement for failed main control modules.

This replacement strip restores a clean, factory fit where it's used on the appliance. Replacing a worn or missing strip helps secure adjoining pieces, maintain spacing, and eliminate unsightly gaps or vibration-related noise. What it does:

• Acts as a finishing/spacer strip between adjoining components
• Helps hold trim or panel pieces in the correct position
• Maintains alignment and clearances to prevent rubbing or rattling
• Common symptoms: cracked or missing strip, visible gap, loose trim/panel, buzzing or vibration noises

• 1 strip

• Disconnect power and, if applicable, shut off water before servicing
• Refer to your model's parts diagram for the correct orientation and attachment points
• Reuse original screws/clips if required; hardware is typically model-specific
• After installation, verify proper alignment and operation of adjacent panels/doors

This is a small wheel designed for use in a refrigerator or freezer, typically mounted on a shelf, drawer, or rack to allow smooth sliding in and out. It helps support the weight of stored items while enabling easy access. Replace this wheel if it is cracked, broken, or no longer rolling freely, causing drawers or racks to stick or sit unevenly.

If your freezer isn't maintaining proper temperature or runs constantly, the temperature sensor may have failed. This sensor monitors interior temps.

Secures and guides your refrigerator door for smooth opening and closing. Replace if your door sags, doesn't align, or fails to seal properly. Verify fit with your model number.

Factory trim strip that finishes edges and covers seams on your refrigerator. Replace if cracked, worn, or missing to restore clean appearance.

This is a filter drier used in the sealed refrigeration system to remove moisture and contaminants from the refrigerant lines. It is a small cylindrical component typically located along the refrigerant tubing between the condenser and the capillary tube. Replace this part if the refrigerator or freezer is not cooling properly due to a restricted or saturated drier, typically during a sealed system repair.

The Insert is an OEM part for Bosch ovens. It secures and stabilizes the oven door handle, ensuring proper alignment and smooth operation.

This insert is engineered to withstand the rigors of regular use, providing a stable and reliable connection between the oven door and the handle.  

Causes of a bad mounting insert can include excessive wear and tear, exposure to high temperatures or moisture, or physical impact that may cause deformation or cracking.

Symptoms of a bad insert include:

• Loose or wobbly door handle
• Difficulty in opening or closing the oven door smoothly
• Misalignment of the handle with the door
• Potential damage to the handle or door due to improper support

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Fix intermittent filling or valve clicking with this refrigerator valve magnet solenoid coil. Restores reliable valve actuation and water flow control.

Fixes no water dispenser or ice maker issues. This inlet valve controls water flow to restore proper fill and prevent leaks in your refrigerator.

This rail guides a dishwasher rack so it slides smoothly in and out, restoring proper rack alignment and reducing jams. It's a direct-fit replacement when an original rail is bent, worn, or broken. What it does

• Guides the rack on its rollers to keep it level and aligned during loading and unloading
• Prevents the rack from binding or derailing while extending or retracting
• Helps restore smooth rack movement if the original rail is bent, cracked, or worn
• Works with the rack rollers and end stops to maintain safe, consistent operation

• One replacement rail

• Basic tools are usually all that's required; verify rail orientation before removing the old part
• Remove the affected rack and rollers as needed to access and replace the rail
• Inspect rollers and end stops while servicing; replace any damaged components for best results
• Disconnect power to the appliance before performing any service that exposes wiring or electrical components

This is a housing component used inside the freezer section of the refrigerator. It serves as a protective enclosure for internal parts such as sensors, lights, or fan assemblies, helping to keep them properly positioned and shielded. Replace this housing if it is cracked, broken, or warped, which can affect the proper operation of the components it protects.

The ice maker assembly is the complete ice-producing unit located in the freezer compartment that includes the motor, mold, and harvest components. Replace when it stops making ice entirely, produces malformed ice, or makes excessive noise during operation.

This operating module is the electronic control that manages your appliance's user commands and cycle functions, restoring reliable control and responsive operation when the original module fails. What it does:

• Receives and processes user inputs from the control panel so cycles start and run correctly
• Controls timing, indicators and interlocks for proper cycle sequencing
• Replaces a failed control to stop issues like unresponsive buttons, missing displays, or erratic cycle behavior
• Works as the central logic board coordinating sensors and actuators during operation

• One operating module (electronic control) as shown

• Disconnect power (unplug or switch off breaker) before starting any repair
• Handle the module carefully; avoid static discharge and secure connectors firmly
• Require removal of the front console or control panel to access; keep fasteners and trim parts organized

Fix a refrigerator that won't cool or runs constantly with this compressor. Circulates refrigerant through the cooling system to maintain proper temperatures.