Bosch Refrigerator B30BB930SS Parts

A replacement handle strip that restores the finished look and cover at the appliance door handle area. Replaces worn, scratched or missing trim to improve appearance and protect handle mounting points. What it does:

• Covers the door handle area and provides a finished trim piece
• Hides mounting hardware and helps prevent dirt buildup around the handle
• Restores cosmetic appearance when original trim is scratched, dented, or missing
• Used with original handle assembly to complete the door finish

• Disconnect power to the appliance before beginning any repair
• Handle carefully to avoid scratches; use proper tools and follow OEM instructions

This replacement strip restores a clean, factory fit where it's used on the appliance. Replacing a worn or missing strip helps secure adjoining pieces, maintain spacing, and eliminate unsightly gaps or vibration-related noise. What it does:

• Acts as a finishing/spacer strip between adjoining components
• Helps hold trim or panel pieces in the correct position
• Maintains alignment and clearances to prevent rubbing or rattling
• Common symptoms: cracked or missing strip, visible gap, loose trim/panel, buzzing or vibration noises

• 1 strip

• Disconnect power and, if applicable, shut off water before servicing
• Refer to your model's parts diagram for the correct orientation and attachment points
• Reuse original screws/clips if required; hardware is typically model-specific
• After installation, verify proper alignment and operation of adjacent panels/doors

Secures and guides your refrigerator door for smooth opening and closing. Replace if your door sags, doesn't align, or fails to seal properly. Verify fit with your model number.

Factory trim strip that finishes assembly edges on select appliances. Replace cracked, broken, or missing strips to restore a clean appearance.

Replacement mounting bracket that secures internal components and maintains proper alignment. Needed when original support is cracked, broken, or loose.

This support mounting bracket secures internal components and helps keep assemblies aligned for reliable operation. It replaces worn or damaged supports to restore proper fit and reduce movement that can cause noise or poor performance. What it does:

• Provides structural support to hold panels, housings, or assemblies in correct position
• Prevents sagging, misalignment, and excessive vibration or rattling during operation
• Restores secure mounting where original bracket is cracked, bent, or broken
• Helps maintain proper clearances to avoid rubbing or interference with moving parts

• One support (mounting bracket)

• Disconnect power and water before beginning any repair
• Use basic hand tools; handle sharp edges carefully and wear gloves
• Verify correct orientation and secure fasteners to manufacturer torque specs when available

This replacement strip is a molded trim piece that covers and protects an appliance panel edge for a clean finished appearance and helps keep wiring and components tucked away. It restores the original look and helps prevent snags or abrasions. What it does:

• Covers exposed panel edges and seams for a finished appearance
• Holds and protects underlying components or wiring from contact
• Prevents fabric/snags and reduces the chance of accidental catching on the edge
• Helps maintain the appliance's original fit-and-clearance where installed

• One strip/trim piece as shown

• Disconnect power to the appliance before starting any work
• Installation may require removing the outer panel or control panel to access mounting area
• Handle carefully to avoid scratching the finish; use non-marring tools as needed
• If fasteners, clips, or adhesive are required, reuse the factory hardware or replace with OEM-specified parts

This replacement cover shields and secures a designated opening or component inside the appliance. It helps protect internal parts from debris and accidental contact to maintain safe operation and a clean, finished appearance.

• Provides a protective barrier over an opening or assembly to shield internal components
• Restores proper fit and appearance when the original cover is cracked, warped, or missing
• Helps reduce rattling or vibration caused by a loose or damaged cover
• Ensures the area remains securely closed when tabs/fasteners are properly engaged

• Disconnect power before servicing; shut off water supply if applicable
• Note the orientation of the original cover; transfer any clips/seals/screws if designed to be reused
• Seat the new cover fully and engage all locking tabs or fasteners; do not overtighten
• The cover stays secure and does not interfere with adjacent parts during operation

Fix frost buildup in your freezer with this refrigerator defrost heater. Melts ice on evaporator coils to restore proper cooling. Moderate DIY repair.

The Water Valve is an OEM part for Bosch refrigerators. It controls the flow of water to the ice maker and water dispenser components within the refrigerator.

Causes of a malfunctioning Water Valve can include sediment buildup clogging the valve and restricting water flow. 

Symptoms of a bad Water Valve include:

• No water dispensing from the door dispenser
• The ice maker not producing ice or producing incomplete ice cubes
• Leaks or water puddles around the valve area inside the refrigerator

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Fixes no water dispenser or ice maker issues. This inlet valve controls water flow to restore proper fill and prevent leaks in your refrigerator.

This power module is the main control board that supplies and manages electrical power to the appliance's systems, restoring normal operation when the original module fails. Replacing a faulty power module can stop intermittent power issues and restore control functions. What it does:

• Regulates and distributes electrical power to the appliance's control circuits
• Replaces failing electronics that cause no-power, no-start, or random shutdowns
• Resolves control-panel failures and erratic operation tied to power faults
• Helps restore reliable communication between user controls and internal components

• Disconnect all power (unplug or switch off circuit breaker) before servicing
• Handle the board by its edges and avoid static discharge — use a grounding strap if available
• Verify the symptom and test electrical connections before replacing the module

This fan is the OEM-style cooling blower used to circulate air for component and cabinet cooling. It restores proper airflow to help reduce overheating, excessive noise, and cooling-related performance issues. What it does

• Circulates air across motors, electronics, or heat exchangers to maintain safe operating temperatures.
• Helps prevent overheating and thermal shutdowns by moving warm air away from components.
• Reduces noise and vibration when a worn or imbalanced fan is replaced.
• Common symptom: loud or rattling noise, weak/no airflow, or intermittent thermal-related faults.

• Disconnect power to the appliance before starting any repair.
• Handle the fan and surrounding components carefully; avoid bending blades or damaging the motor leads.
• Verify mounting orientation and secure all fasteners; wiring connections match the original.
• After installation, restore power and run the appliance to confirm normal airflow and quiet operation.

This blower fan assembly circulates air to cool and ventilate the appliance, helping maintain proper operating temperature and airflow for reliable performance. It replaces a worn or noisy fan to restore normal ventilation. What it does:

• Moves air through the appliance to prevent overheating of components
• Reduces unusual noise or vibration caused by a failing fan
• Helps maintain consistent internal temperatures for proper operation
• Supports cooling of motors, electronics, or heating compartments as applicable

• One blower fan assembly (motor with attached fan blade)

• Disconnect power before attempting any service to avoid shock or injury
• Access may require removing panels or housing; keep track of fasteners
• Inspect mounting and wiring; replace only if confirmed compatible with your model

This inverter is the electronic motor-speed control board that regulates power and variable speed to the appliance's motor for reliable operation. Replaces a failed inverter to restore drive/motor control. What it does:

• Converts and regulates incoming power to the motor for variable-speed operation
• Controls motor start/stop and speed changes during cycles
• Helps prevent motor stalling and uneven operation when functioning correctly
• Common symptom link: appliance won't start, motor hums, or motor does not reach proper speeds
• Associated with control or drive-related error codes

• Disconnect power before accessing or replacing the inverter to avoid shock
• Handle the board carefully and avoid bending or touching exposed components
• Observe basic ESD precautions (grounding) when handling electronic boards