Bosch Refrigerator B30IR900SP Parts

Bad taste or odor in water and ice? This refrigerator water filter removes impurities for clean, fresh-tasting water. Easy DIY install in minutes.

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

This sensor monitors operating conditions inside the appliance and reports to the control so cycles run correctly and safely. When the sensor fails, the control may receive inaccurate feedback, leading to irregular performance. What it does:

• Detects key conditions inside the appliance and sends a signal to the control
• Helps the control regulate heat and cycle progress
• Failure symptoms can include erratic cycle times, poor heating performance, or sensor-related error messages
• Can prevent the appliance from starting or completing a cycle if readings are out of range

• 1 sensor

• Disconnect power before servicing; shut off water supply if applicable
• Access the sensor and note wire orientation before removal
• Ensure any sealing surface is clean and the sensor is seated properly; check for leaks after reassembly where applicable
• Run a diagnostic or test cycle after installation to clear errors and verify operation

The FIXTURE is an OEM replacement part for Bosch freezers. Typically located inside the fresh food compartment, fixtures hold slidable wire shelves, bins, crispers, and other removable storage accessories in precise positions.

Causes of a faulty fixture can include cracking or breaking of plastic rails from repeated impact or overloading. Clips and mounting attachments may also loosen over time.

Symptoms of a bad fixture include: 

• Shelves, bins, and pans that no longer slide smoothly or feel insecure
• Storage accessories like crispers that tilt or are difficult to remove
• Interior rattles or banging noises coming from loose components

This replacement Bosch fixture returns stability and structure to the organization system. Realigning fixtures maintains consistent placement and secure engagement of accessories for tidy, accessible food storage. 

Compatible with Thermador, Gaggenau, or Kenmore French door models utilizing consistent interiors.

Mounting hardware kit secures refrigerator components in place. Replaces worn, missing, or damaged fasteners that cause rattling or loose parts inside unit.

This hinge pin secures the door hinge mechanism and allows your refrigerator or freezer door to pivot smoothly. It maintains proper door alignment and prevents the door from sagging or binding. Replace this part if your door won't close properly, sags when opened, or if you hear squeaking or grinding when opening the door.

Trim strip that provides a finished edge and protective cover at its mounting location. Replace when cracked, worn, or missing to restore proper appearance.

Replacement access panel cover that shields internal components. Restores a finished look when the original is cracked, broken, or missing.

Vertical trim strip that covers the gap between refrigerator doors. Replace if cracked, chipped, discolored, or missing to restore a clean appearance.

Routes water around the fine filter area when servicing your dishwasher. Replace if damaged or missing to maintain proper wash circulation. Verify fit.

Replace a frayed or damaged power cord that's causing no power or intermittent operation. Direct plug-in replacement restores safe electrical connection.

Decorative trim piece that finishes panel or door edges on appliances. Replace worn, cracked, or missing strips to restore a clean factory look.

This evaporator fan circulates cold air through the freezer/refrigerator evaporator to help maintain even cooling and proper temperature. Replacing a worn or noisy fan can restore airflow and improve cooling performance. What it does:

• Moves air across the evaporator coil to distribute cold air throughout the compartment
• Helps prevent frost buildup by maintaining steady airflow over the evaporator
• A noisy, vibrating, or non-spinning fan can cause poor cooling or uneven temperatures
• Restores proper circulation when the original fan motor or blade is damaged or fails

• One evaporator fan assembly

• Disconnect power to the appliance before attempting any repair to avoid electric shock
• Access may require removing interior panels or the evaporator cover; follow OEM diagram for your model
• Handle the fan blades and motor carefully to avoid bending blades or damaging the motor shaft

Secures and guides your refrigerator door for smooth opening and closing. Replace if your door sags, doesn't align, or fails to seal properly. Verify fit with your model number.

Protective cover housing that shields internal components from debris and moisture. Replace if your original housing is cracked, broken, or missing.