Bosch Refrigerator B36IT900NP Parts

Stores and dispenses ice cubes in your refrigerator freezer. Replace a cracked, warped, or missing ice bin to keep cubes contained and hygienic.

Replace a frayed or damaged power cord that's causing no power or intermittent operation. Direct plug-in replacement restores safe electrical connection.

Electronic power module for the dishwasher. This is the main control board that manages power and timing for wash, drain, and drying functions, helping restore normal operation when the original module has failed or is intermittent.

• Regulates incoming power and switches major loads (circulation pump, drain pump, heater, inlet valve)
• Coordinates cycle logic based on door and sensor inputs
• May help when the dishwasher won't power on or start a cycle
• May help when cycles stop mid-way, don't complete, or drying performance is poor

• Disconnect electrical power at the circuit breaker before servicing
• Access is typically from behind the lower toe panel/base; remove panels as needed
• Photograph and label wiring; transfer any mounting hardware; seat connectors fully
• Use ESD protection and handle the board by its edges only

This factory strip is a trim piece that finishes and protects an exposed edge or gap on your appliance. Replacing a cracked or missing strip restores a clean look and helps panels align and stay secure. What it does

• Finishes an exposed seam or edge as designed by the manufacturer
• Helps keep adjacent panels aligned and secure
• Can reduce vibration-related rattles when properly seated
• Common signs of failure: loose or missing trim, visible gaps, warping, cracks, or buzzing/rattling noises

• 1 strip

• Disconnect power and, if applicable, shut off water before servicing
• Note the strip's orientation; remove any screws/clips and gently release tabs
• Reuse or transfer original fasteners/clips as required by your model
• Align carefully and avoid overtightening to prevent damage to the strip or surrounding panels

A replacement handle strip that restores the finished look and cover at the appliance door handle area. Replaces worn, scratched or missing trim to improve appearance and protect handle mounting points. What it does:

• Covers the door handle area and provides a finished trim piece
• Hides mounting hardware and helps prevent dirt buildup around the handle
• Restores cosmetic appearance when original trim is scratched, dented, or missing
• Used with original handle assembly to complete the door finish

• Disconnect power to the appliance before beginning any repair
• Handle carefully to avoid scratches; use proper tools and follow OEM instructions

This replacement strip restores a clean, factory fit where it's used on the appliance. Replacing a worn or missing strip helps secure adjoining pieces, maintain spacing, and eliminate unsightly gaps or vibration-related noise. What it does:

• Acts as a finishing/spacer strip between adjoining components
• Helps hold trim or panel pieces in the correct position
• Maintains alignment and clearances to prevent rubbing or rattling
• Common symptoms: cracked or missing strip, visible gap, loose trim/panel, buzzing or vibration noises

• 1 strip

• Disconnect power and, if applicable, shut off water before servicing
• Refer to your model's parts diagram for the correct orientation and attachment points
• Reuse original screws/clips if required; hardware is typically model-specific
• After installation, verify proper alignment and operation of adjacent panels/doors

The Sensor is an OEM component specifically designed for Bosch refrigerators. It plays an integral role in monitoring temperature and humidity levels inside the refrigerator and freezer compartments. The sensor works together with the electronics package to regulate cooling power to maintain consistent performance.

Some causes of a bad sensor can include damage due to frequent temperature fluctuations, moisture intrusion into the sensor area, or failure of the electronic components. 

Symptoms of a bad sensor include: 

• Inconsistent or fluctuating temperatures inside the fridge/freezer
• Ice buildup in undesired areas 
• Food not staying fresher for as long 
• Error codes displayed related to sensor issues

This Bosch sensor part is compatible with Thermador, Gaggenau, and some Kenmore models as well. Replace yours today with this genuine OEM sensor to restore proper cooling functionality.

Replacement mounting bracket that secures internal components and maintains proper alignment. Needed when original support is cracked, broken, or loose.

This support mounting bracket secures internal components and helps keep assemblies aligned for reliable operation. It replaces worn or damaged supports to restore proper fit and reduce movement that can cause noise or poor performance. What it does:

• Provides structural support to hold panels, housings, or assemblies in correct position
• Prevents sagging, misalignment, and excessive vibration or rattling during operation
• Restores secure mounting where original bracket is cracked, bent, or broken
• Helps maintain proper clearances to avoid rubbing or interference with moving parts

• One support (mounting bracket)

• Disconnect power and water before beginning any repair
• Use basic hand tools; handle sharp edges carefully and wear gloves
• Verify correct orientation and secure fasteners to manufacturer torque specs when available

This is a small wheel designed for use in a refrigerator or freezer, typically mounted on a shelf, drawer, or rack to allow smooth sliding in and out. It helps support the weight of stored items while enabling easy access. Replace this wheel if it is cracked, broken, or no longer rolling freely, causing drawers or racks to stick or sit unevenly.

Secures and guides your refrigerator door for smooth opening and closing. Replace if your door sags, doesn't align, or fails to seal properly. Verify fit with your model number.

Factory trim strip that finishes edges and covers seams on your refrigerator. Replace if cracked, worn, or missing to restore clean appearance.

Factory trim strip that finishes assembly edges on select appliances. Replace cracked, broken, or missing strips to restore a clean appearance.

This replacement cover shields and secures a designated opening or component inside the appliance. It helps protect internal parts from debris and accidental contact to maintain safe operation and a clean, finished appearance.

• Provides a protective barrier over an opening or assembly to shield internal components
• Restores proper fit and appearance when the original cover is cracked, warped, or missing
• Helps reduce rattling or vibration caused by a loose or damaged cover
• Ensures the area remains securely closed when tabs/fasteners are properly engaged

• Disconnect power before servicing; shut off water supply if applicable
• Note the orientation of the original cover; transfer any clips/seals/screws if designed to be reused
• Seat the new cover fully and engage all locking tabs or fasteners; do not overtighten
• The cover stays secure and does not interfere with adjacent parts during operation

A replacement profile stripe — the decorative trim piece that restores your appliance's finished look. Replaces a scratched, faded, or missing stripe to improve appearance and maintain original styling. What it does:

• Covers and finishes the appliance front for a clean, uniform appearance
• Hides minor edge gaps where panels meet for a seamless look
• Restores original styling after damage or paint wear
• Helps maintain resale value by keeping the exterior looking factory-fresh

• One profile stripe decorative trim piece

• Cosmetic part; installation may require removing the outer panel or trim clips
• Turn off power to the appliance before removing panels to avoid injury
• Use gentle tools to pry clips or adhesive; avoid bending the stripe or surrounding panels
• Replace with OEM-approved parts for best fit

This is a filter drier used in the sealed refrigeration system to remove moisture and contaminants from the refrigerant lines. It is a small cylindrical component typically located along the refrigerant tubing between the condenser and the capillary tube. Replace this part if the refrigerator or freezer is not cooling properly due to a restricted or saturated drier, typically during a sealed system repair.