Bosch Range HDI8056U Parts

Replacement door handle for wall ovens and ranges. Installs on the oven door for safe opening and closing. Replace if cracked, broken, or missing.

Replacement drawer front panel for ranges. Restores appearance and proper fit when the original is cracked, dented, scratched, or missing. Single drawer style.

Replacement mounting nut for securing internal oven and range components. Needed when original fastener is stripped, missing, or damaged during repair work.

Restore even baking when your oven heats unevenly. This convection fan blade circulates hot air for consistent cooking. Moderate DIY install.

This is a gas valve that controls the flow of gas to an individual surface burner on a gas range or cooktop. It connects to the burner control knob and regulates the flame from high to low settings. Replace this valve if a burner will not ignite, the flame cannot be adjusted properly, or you detect a gas smell when the knob is in the off position.

Fixes inconsistent flames or weak heating on your range. This gas pressure regulator stabilizes fuel flow to burners for reliable cooking performance.

Fix intermittent power or electrical faults in your range with this cable harness. Routes power and signals between control and components. Direct fit.

Mounting screw for ranges and cooktops. Secures panels, brackets, and components during installation. Replace if lost, stripped, or damaged.

Secures flexible hoses to fittings on your range to prevent leaks. Replace if connections are loose or clamp is damaged. Verify fit with your model.

Replacement end cap for oven door handles. Fits at either end of the handle assembly to provide a finished look and comfortable grip. Replace if cracked or missing.

This cable harness connects and routes power and signal lines between appliance components to restore reliable electrical connections. It replaces damaged or worn wiring to help resolve intermittent operation or loss of power to affected parts. What it does:

• Provides secure electrical connections between control boards, sensors, and motors
• Replaces frayed, broken, or corroded wiring that can cause intermittent faults
• Can stop symptoms like components not powering, erratic behavior, or communication errors
• Keeps wiring organized and routed to reduce strain and chafing

• One cable harness as shown

• Always disconnect power before starting any repair
• Match connectors and routing to the original harness; secure with existing clips or ties
• Inspect mating connectors and terminals for damage or corrosion before installation

This replacement routing tube channels fluid inside the appliance to restore proper flow and stop leaks. It replaces a damaged, cracked, or clogged tube to help prevent water pooling and restore normal operation. What it does:

• Routes water or condensate between internal components to maintain proper drainage or flow
• Replaces cracked, split, or deteriorated tubing that can cause leaks or puddles
• Helps eliminate intermittent dripping or loss of water flow caused by blockages or holes
• Works as a direct-fit replacement when the original tubing has failed

• One replacement tube

• Disconnect power and shut off the water supply before installing
• Inspect and reuse or replace any retaining clips, clamps, or grommets as needed
• Slide tube fully into fittings and secure with appropriate clamps to prevent leaks

This is the inner door panel that forms the interior-facing surface of the oven door. It provides structural support for the door assembly and helps contain heat within the oven cavity. Replace this panel if it is warped, cracked, rusted, or if the oven door is not sealing properly and allowing heat to escape.

Range not heating properly or taking too long to warm up? This heating element restores proper temperature control. Moderate difficulty repair in 30-45 minutes.

This retaining washer secures a control shaft or hub to keep components in place during operation, helping restore proper control movement and prevent parts from sliding off the shaft. Simple replacement when a worn or missing retainer causes loose knobs or shifting parts. What it does:

• Fits onto a control or drive shaft to hold a knob, hub or gear in position
• Prevents axial movement that can cause loose or slipping controls
• Commonly replaced when the original washer is bent, cracked, or lost
• Works with compatible Bosch control assemblies and hubs

• One retaining washer

• Recommended for users comfortable with basic appliance disassembly; unplug appliance before starting
• Remove the control knob or panel per model instructions to access the shaft
• Press the washer into place on the shaft until fully seated; verify proper fit and control operation

This is a spacer insert that fits behind or between the oven door handle and the outer door panel, ensuring the handle is properly positioned and securely mounted. It helps maintain the correct gap and alignment for the door handle assembly. Replace this part if the door handle feels loose, sits unevenly, or if the original spacer is cracked or missing.