Bosch Range HGIP056UC Parts

Uneven baking or slow cooking? This convection fan circulates heated air throughout your range oven for consistent, professional cooking results.

Fixes burner flame issues on gas ranges. Controls gas flow for consistent cooking temperatures. Replacing a worn valve restores precise flame control.

Replacement tube that channels water inside the appliance to restore proper flow and help prevent leaks, pooling, or poor performance when the original is cracked, kinked, or deteriorated for reliable operation. What it does:

• Routes water between internal components to maintain normal circulation.
• Stops properly when replaced if the original is cracked, split, hardened, or leaking.
• Common symptoms indicating replacement: visible leaks, puddling under the appliance, reduced water flow, or inconsistent cycle performance.
• Reinstall with proper clamps and routing to avoid kinks and ensure a watertight connection.

• Disconnect power and shut off the water supply before starting any repair.
• Drain remaining water and relieve pressure in lines to minimize spills.
• Remove access panels as needed and note the tube routing/orientation before removing the old part.
• Install the new tube without sharp bends, secure with the correct clamps or fittings, then restore power/water and check thoroughly for leaks.

The Screw is an OEM part for Bosch gas cooktops and ranges. It anchors the surface burner head assembly onto the cooktop surface.

Causes can be stripped threads or overall wear from repeated heating/cooling cycles. Exposure to cooking spills or impacts may also deteriorate the screw head over time.

Symptoms of a bad burner head screw include:

• A burner detaching from the cooktop surface entirely
• Excess movement or instability of burner heads when in use
• Gas leaks reported around the burner head connection points

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This water inlet valve controls the flow of water into the appliance, restoring proper filling and preventing overfill when working correctly. Fits specific BOSCH machines and replaces a worn or failed inlet valve. What it does:

• Opens and closes to allow water into the appliance when a cycle calls for fill
• Helps maintain correct water level so cycles run and clean properly
• Failsafe against continuous fill when functioning correctly; common fault causes no-fill or constant-fill symptoms
• Often replaced when appliance leaks, won't fill, or runs continuously without stopping

• One water inlet valve

• Disconnect power and shut off water supply before attempting replacement
• Handle electrical connections and inlet lines carefully; inspect seals and hoses and replace if worn

This is a 6-inch drip bowl that sits beneath the surface burner element on an electric range or cooktop. It catches spills and drips while reflecting heat upward toward the cookware for more efficient heating. Replace this drip bowl if it is warped, corroded, heavily stained, or no longer sitting flat under the burner element.

Replaces cracked, chipped, or fogged oven door inner glass. Restores clear viewing and proper heat retention. Confirm fit with your model number.

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

Halogen oven light bulb illuminates the oven cavity for clear viewing during cooking. Replace when dim or burned out. Verify fit with your model.

Fix intermittent power or component failure with this range socket electrical connector. Restores secure wiring connections in electric and gas ranges.

This is a stainless-finish control knob used on the cooktop or cooking area of a range. It attaches to a control shaft and allows you to adjust the burner or surface element temperature settings. Replace this knob if it is cracked, the finish is worn, or the knob spins freely without engaging the control shaft.

Replacement mounting screw for securing panels, brackets, and components in ranges and wall ovens. Restores proper fit if original is missing or stripped.

This small rubber ring seals the gap between the control knob and the range surface, preventing spills and debris from entering the control mechanism. Replace when the gasket becomes cracked, torn, or missing, allowing liquids to seep behind the control panel or causing the knob to feel loose.

The Insert is an OEM part for Bosch ovens. It secures and stabilizes the oven door handle, ensuring proper alignment and smooth operation.

This insert is engineered to withstand the rigors of regular use, providing a stable and reliable connection between the oven door and the handle.  

Causes of a bad mounting insert can include excessive wear and tear, exposure to high temperatures or moisture, or physical impact that may cause deformation or cracking.

Symptoms of a bad insert include:

• Loose or wobbly door handle
• Difficulty in opening or closing the oven door smoothly
• Misalignment of the handle with the door
• Potential damage to the handle or door due to improper support

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Burner is an OEM part for Bosch ranges and cooktops. The burner head features precision engineered ports that allow for the proper mixing of gas and air, ensuring efficient and even combustion.

Causes of a bad gas burner head can include clogging or blockages of the small flame ports, cracks or breaks in the metal head casing from long term heat exposure or accidental damage.

Symptoms of a bad gas burner head include:

• Uneven or irregular flame patterns
• Flames that blow out easily or are difficult to ignite
• Reduced heating power and ineffective cooking
• Gas leaks from cracks or breaks in the head casing

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Replacement door handle for wall ovens and ranges. Installs on the oven door for safe opening and closing. Replace if cracked, broken, or missing.