Bosch Microwave HMV8044U Parts

Secures panels, brackets, and components inside your microwave or wall oven. Replace missing, rusted, or stripped screws to restore proper fit.

Replacement mounting nut that secures panels, brackets, or assemblies inside your microwave or wall oven. Needed when original is stripped, missing, or worn.

This motor start/run capacitor helps the appliance's motor start smoothly and run more efficiently. Replacing a failing capacitor can restore normal motor operation and reduce humming or intermittent motor stops. What it does:

• Provides the temporary energy boost the motor needs to start and maintain proper speed.
• Commonly linked to symptoms such as motor humming, slow motor start, or motors that stall or run inconsistently.
• Works with the motor's starting circuit to stabilize performance during load changes.
• Matches the original function and electrical role of the factory-installed capacitor when replaced with the correct part number.

• One capacitor as shown.

• Disconnect power to the appliance before attempting any repair.
• Discharge the capacitor safely (use insulated tools and follow manufacturer procedures) to avoid electrical shock.
• Replace only with a capacitor that matches the original specifications and mounting.

This drive shaft is the rotating spindle that links the dishwasher's motor to the lower pump/impeller assembly, restoring powered water circulation for normal wash performance. It's a direct-fit replacement designed to match OEM form and fit. What it does:

• Transmits motor rotation to the pump/impeller so water is circulated during the wash cycle
• Restores normal spray and drain function when a worn or broken shaft prevents pump operation
• Helps eliminate grinding, wobbling, or no-water-flow symptoms caused by a damaged drive connection
• Works with the dishwasher's lower sump/pump assembly to maintain sealed, aligned rotation

• One drive shaft

• Disconnect power and water before starting any repair; follow all safety precautions
• Access typically requires removal of the dishwasher base/sump and disassembly of the pump housing
• Inspect surrounding seals, bearings, and impeller for wear and replace as needed

Replacement mounting screw for microwave panels and components. Secures brackets, trim pieces, and internal parts. Needed when original is stripped, lost, or damaged.

This grille is the exterior vent trim piece that finishes the lower front of the appliance and helps direct airflow while keeping internal components protected and looking finished. It restores the appliance's appearance and proper ventilation. What it does:

• Covers and protects the lower vent area to prevent debris from entering internal components
• Provides a finished appearance to the appliance front where venting occurs
• Helps direct airflow from the vent opening for normal operation
• Replaces damaged, cracked, or broken trim that can detract from appearance or airflow

• One grille / vent trim piece as shown

• Designed to be installed without modifying the appliance; refer to your model's service manual for exact removal and replacement steps
• Power off and, if applicable, unplug the appliance before attempting removal or installation
• Handle carefully to avoid scratching painted or plated surfaces; use non-marring tools when needed
• If fasteners are missing or damaged, replace with OEM-specified hardware

If your microwave overheats or runs louder than normal, a worn cooling fan blade may be the cause. This part circulates air to prevent damage.

This is a cutting grid assembly designed for a food preparation appliance. It features a grid of blades or wires used to dice or cut food items into uniform pieces. Replace this grid if the blades are dull, bent, or broken, or if food is no longer being cut evenly.

Inner door access cover shields internal wiring and controls behind the microwave door. Replace if cracked, broken, or missing to restore protection.

If your microwave is overheating or running louder than usual, a worn fan blade may be the cause. This impeller restores proper airflow and cooling.

If your microwave is overheating or making loud grinding noises, the fan motor may have failed. This part circulates air to cool internal components.

This is a cover or bracket that sits over the stirrer blade assembly inside the microwave cavity, typically mounted on the ceiling of the interior. The stirrer blade beneath it rotates to distribute microwave energy evenly for consistent cooking. Replace this cover if it is cracked, warped, scorched, or if you notice uneven heating or arcing inside the microwave.

Mounting screw for microwave installation and assembly. Replaces lost, stripped, or damaged screws that secure panels, brackets, or components.

Mounting screw for microwave installation and assembly. Replaces lost, stripped, or corroded screws used to secure panels, brackets, or hardware.