Bosch Freezer KAD62S20 Parts

This is a plastic drip tray that sits beneath the water or ice dispenser on the front of your refrigerator to catch spills and drips. It snaps into place and can be removed for easy cleaning. Replace this tray if it is cracked, warped, discolored, or no longer fits securely in its mounting position.

This replacement tray is a removable cutlery and utensil insert that helps organize silverware for thorough cleaning and easy unloading. Fits into the dishwasher's rack to keep items separated and positioned during a wash cycle. What it does:

• Holds forks, knives, spoons and small utensils securely in the rack so water reaches all surfaces
• Prevents items from nesting together for improved cleaning performance
• Keeps sharp utensils contained for safer loading and unloading
• Helps reduce movement and noise of loose utensils during a cycle

• One replacement tray/utensil insert

• Place the tray into the designated slot or area in the dishwasher rack until it snaps or rests securely
• Ensure utensils are placed handle-down when recommended by your dishwasher manual to avoid blocking spray arms
• Do not force the tray into place; check alignment with rack guides to prevent damage
• Disconnect power to the appliance before attempting any repairs that require disassembly beyond removing the tray

Refrigerator not cooling or running constantly? The condenser removes heat from the refrigerant. This repair takes 1-2 hours with moderate skill.

This replacement cover protects internal dishwasher components by sealing the pump/motor area and helping prevent leaks and debris entry. It restores a secure housing interface to keep the appliance operating reliably. What it does:

• Seals the pump/motor housing to help prevent water leaks and contain splashes
• Protects internal components from debris that can cause clogs or wear
• Helps maintain correct component alignment to reduce noise and vibration
• Can be replaced when the cover is cracked, broken, or missing

• Disconnect power and shut off water supply before beginning any repair
• Access may require removing kick plate or inner panels; keep fasteners organized
• Inspect mounting clips, seals, and surrounding components; replace damaged parts as needed

This interference capacitor suppresses electrical noise and radio-frequency interference to help the appliance's electronics run more reliably. It fits on the control board and supports stable operation by filtering stray voltage spikes. What it does:

• Filters electrical and radio-frequency interference that can cause erratic control behavior or false error codes
• Reduces electrical noise that can affect nearby audio or radio reception
• Helps protect control circuitry from transient voltage spikes
• Commonly used when appliance exhibits intermittent faults or unexplained control glitches

• Disconnect power to the appliance before starting any repair
• Discharge capacitors and avoid touching leads; use insulated tools and follow safe-handling practices
• Replace only with the exact part specified for your model and secure all wire connections firmly

Refrigerator not cooling properly or running too warm? This fan motor powers the blower to circulate air and maintain proper temperatures throughout your fridge.

Fixes no water dispensing or slow ice production. This refrigerator water tank stores water for the dispenser and ice maker. DIY-friendly repair.

This door seal fits around the dishwasher tub opening to keep water and steam inside during cycles. Replacing a worn gasket restores a tight seal so the door latches properly and helps prevent leaks at the sides or bottom.

• Creates a watertight barrier between the door and tub during wash and rinse cycles
• Helps contain steam and reduce moisture escaping from the front of the unit
• Replaces a flattened, cracked, torn, or deformed seal that can cause leaks
• Common symptoms include drips at the front edge, water on the floor near the door, and needing extra force to latch

• Disconnect power and, if applicable, shut off the water supply before servicing
• Pull the old seal from the channel; clean the groove and mating surfaces thoroughly
• Press the new seal in evenly without stretching; seat corners fully and position the joint at the bottom center
• Close the door to help the seal set; a snug fit at first is normal

This is a flexible rubber seal that attaches around the perimeter of the freezer door, creating an airtight closure when the door is shut. It prevents warm air from entering the freezer compartment and keeps cold air from escaping. Replace this gasket if you notice frost buildup inside the freezer, the door does not seal tightly, the gasket is torn or warped, or the compressor runs more frequently than normal.

Restores smooth door operation and proper alignment on your refrigerator. Replace when doors wobble, bind, or make noise during opening and closing.

This filter is installed inside or near the crisper drawer compartment to help regulate humidity levels and keep fruits and vegetables fresh longer. It works by controlling airflow and moisture within the drawer. Replace this filter if your produce is wilting or spoiling faster than expected, or if the filter appears dirty or degraded.

Ice dispenser producing large clumps or blocking? This crusher assembly grinds ice into smaller, usable pieces, restoring smooth ice flow and delivery.

This door switch senses the dishwasher door position and tells the control when the door is closed so cycles can start or stop. It restores proper door sensing for reliable operation and safety. What it does:

• Detects when the door is fully closed so the control can begin or continue a wash cycle
• Prevents the dishwasher from starting or running when the door is open
• Common fix for symptoms like no-start, intermittent power to controls, or cycles that stop when the door moves
• Works with the latch/strike assembly to ensure a secure door closure signal

• One door switch

• Always disconnect power at the breaker or unplug the appliance before servicing
• Access typically requires removing the inner door panel; handle the inner door and glass carefully
• Verify wiring orientation and gently disconnect connectors; replace with identical wiring and secure all fasteners
• Test door operation before reassembling the door panels

Replace your broken or missing refrigerator shelf holder. This support piece secures shelves in place. Essential when holders crack or wear out over time.