Bosch Freezer KAD62V40SA Parts

Replace your refrigerator's cracked, broken, or missing glass shelf plate. This transparent storage surface installs on shelf supports inside your fridge.

Refrigerator shelf rail that supports and secures shelf edges. Replace if cracked, broken, or missing to restore proper shelf stability and function.

Replace a cracked or broken shelf rail in your refrigerator. This structural component secures and supports shelves inside the fresh food compartment.

Supports the refrigerator door hinge for smooth, quiet opening and proper alignment. Replace if door catches, squeaks, or binds. Verify fit with your model.

This replacement lid restores the appliance's finished top cover, protecting internal components and helping the door/hatch close properly. Use when the original lid is cracked, warped, or missing to keep the unit looking and operating as intended. What it does:

• Covers and protects the appliance's top/opening area from debris and damage.
• Secures to existing hinge or mounting points to ensure proper closure.
• Replace if you see visible cracks, chips, warping, or if the lid no longer latches or aligns.
• Helps prevent rattling or rubbing caused by a damaged or loose lid.

• Disconnect power (and water, if applicable) before starting any repair.
• Handle edges carefully; some lids include glass or thin sheet material that can chip.
• Basic hand tools (screwdriver/torx) may be required; keep mounting hardware if reusing.

This interference capacitor suppresses electrical noise and radio-frequency interference to help the appliance's electronics run more reliably. It fits on the control board and supports stable operation by filtering stray voltage spikes. What it does:

• Filters electrical and radio-frequency interference that can cause erratic control behavior or false error codes
• Reduces electrical noise that can affect nearby audio or radio reception
• Helps protect control circuitry from transient voltage spikes
• Commonly used when appliance exhibits intermittent faults or unexplained control glitches

• Disconnect power to the appliance before starting any repair
• Discharge capacitors and avoid touching leads; use insulated tools and follow safe-handling practices
• Replace only with the exact part specified for your model and secure all wire connections firmly

Refrigerator not cooling properly or running too warm? This fan motor powers the blower to circulate air and maintain proper temperatures throughout your fridge.

The Motor is an OEM part for Bosch refrigerators. This motor is specifically designed to power the ice dispenser mechanism, allowing for the convenient dispensing of ice cubes or crushed ice. It delivers the necessary power to rotate the dispenser auger, providing you with a steady supply of ice whenever you need it.

A bad motor can occur due to wear and tear, electrical malfunctions, or motor failure. Signs of a faulty motor include the ice dispenser not working, the auger not rotating, or unusual grinding or buzzing noises during ice dispensing.

Symptoms of a bad motor include:

• Inability to dispense ice  
• Noisy or erratic operation 

Replace your malfunctioning or worn-out ice dispenser motor with this genuine OEM Bosch part to restore your refrigerator's ice dispenser. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This door seal fits around the dishwasher tub opening to keep water and steam inside during cycles. Replacing a worn gasket restores a tight seal so the door latches properly and helps prevent leaks at the sides or bottom.

• Creates a watertight barrier between the door and tub during wash and rinse cycles
• Helps contain steam and reduce moisture escaping from the front of the unit
• Replaces a flattened, cracked, torn, or deformed seal that can cause leaks
• Common symptoms include drips at the front edge, water on the floor near the door, and needing extra force to latch

• Disconnect power and, if applicable, shut off the water supply before servicing
• Pull the old seal from the channel; clean the groove and mating surfaces thoroughly
• Press the new seal in evenly without stretching; seat corners fully and position the joint at the bottom center
• Close the door to help the seal set; a snug fit at first is normal

This replacement door seal fits into the groove around the dishwasher opening. It compresses against the door to create a watertight barrier, helping stop front leaks and restore a proper, snug close. What it does:

• Forms a continuous seal to keep wash water inside during all cycles
• Helps the door latch compress correctly for a tight, secure close
• Replaces cracked, flattened, or torn gasket that can drip at corners or along the bottom
• Helps resolve: water on the floor at the front, moisture or steam escaping, door harder to close

• Includes 1 door seal

• Disconnect power and shut off the water supply before servicing
• Pull the old seal straight out of the channel; clean the groove of debris and residue
• Start at the top center; press the new seal evenly into the channel without stretching, ensuring corners are fully seated
• Close and reopen the door to seat the seal; run a short cycle and check for leaks

Restores smooth door operation and proper alignment on your refrigerator. Replace when doors wobble, bind, or make noise during opening and closing.

Approximate dimensions: 16.5" x 11.5" x 0.25"

This tray is a direct-replacement interior component that catches and channels water or debris so your appliance runs cleanly and reliably. It restores proper containment and support where a cracked or warped tray causes messes or leaks. What it does:

• Collects and channels water, drips, or debris away from sensitive components
• Supports internal parts or assemblies that sit on the tray
• Helps prevent leaks or water pooling that can cause odor or damage
• Common symptom: visible cracks, warping, or recurring water beneath the appliance
• Common symptom: loose or misaligned internal parts that previously rested on the tray

• One replacement tray

• High-level swap: remove access panels or racks as needed, unseat the old tray, and position the new tray until it snaps or screws into place
• Use basic hand tools; keep fasteners and any gaskets with the assembly
• Turn power and water supply off before servicing appliances where applicable