Bosch Dishwasher SHP878WD2N Parts

Complete installation hardware set for dishwashers. Includes mounting brackets, screws, and fasteners needed to secure your dishwasher properly.

Dishwasher repair set includes essential components for maintenance and fixes. Replace when parts show wear or damage. Verify fit with your model number.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Fix unresponsive buttons or cycles not starting with this dishwasher control board module. Restores electronic controls and cycle selection functions.

This insulating part provides a non-conductive, heat-resistant barrier between adjacent components inside the appliance. Replacing a damaged insulator helps prevent unintended contact and heat transfer, supporting safe, reliable operation and protecting nearby parts. What it does:

• Electrically isolates terminals or metal surfaces to help prevent shorts or arcing
• Reduces heat transfer to surrounding components
• Maintains proper spacing and support for the protected component
• Replace if the original is cracked, deformed, missing, or shows burn/discoloration

• 1 insulating part

• Disconnect power before servicing; shut off gas or water if applicable
• Access the component, note orientation/positioning of the original insulator, and transfer any clips or hardware as required
• Seat the new insulator fully and ensure no conductive parts touch unintended surfaces
• Reassemble, restore power, and verify normal operation with no rubbing, arcing, or overheating

Restores the exterior finish of your dishwasher door when the original panel is damaged, cracked, or missing. Protects inner components and provides a clean look.

Dishwasher making unusual noise or components overheating? This insulation shield acts as a thermal and electrical barrier, protecting wiring and reducing vibration contact. Simple DIY fix.

Dishwasher mounting clip secures components in place. Replace if clip is cracked, broken, or missing to restore proper fit and stability of parts.

Replacement access panel cover for your dishwasher. Restores proper fit when the original is cracked, broken, or missing. Protects internal components.

Replacement silverware basket insert for your dishwasher lower rack. Order a new insert if yours is cracked, broken, or missing to organize utensils.

This insulating part is a molded insulator that protects nearby components by reducing heat transfer and providing electrical isolation, helping prevent heat damage and short circuits for safer, more reliable appliance operation. What it does:

• Provides thermal insulation to limit heat transfer from hot components to surrounding parts
• Offers electrical isolation to help prevent shorts between conductors or grounded metal
• Maintains proper spacing and support for wiring or small assemblies
• Helps prevent symptoms such as scorch marks, melted wiring insulation, burning smells, or intermittent electrical behavior

• Disconnect power to the appliance before attempting any repair
• Inspect the surrounding area and the old insulator's location and orientation before removal
• Replace with the same part and orientation; avoid compressing or deforming the insulator

This facia panel is the exterior trim piece that restores the appliance's front appearance and provides the finished surface around the control area. It replaces a cracked, scratched or otherwise damaged control-panel face to improve looks and function. What it does

• Covers and protects the control area and underlying components from dirt and damage
• Restores a flat, finished appearance to the appliance front after wear or impact
• Provides the mounting surface and alignment for control buttons and indicators
• Helps prevent moisture and debris from entering the control cavity

• Disconnect power to the appliance before starting any repair
• Remove any trim or bezels to access and replace the panel
• Handle edges carefully to avoid cuts; keep fasteners organized for reassembly
• If the panel secures or aligns controls, verify button alignment and operation after installation