Bosch Dishwasher SHP878WD2N Parts

Fix a dishwasher that won't start, stops mid-cycle, or has error codes with this pre-programmed power module control board. Manages all wash functions.

Secures panels, brackets, and trim pieces inside your dishwasher. Replace this fastener if stripped, missing, or damaged to restore tight assembly.

This support is a factory replacement component that holds and stabilizes a specific part within your appliance so it stays aligned and secure. Replacing a cracked or missing support restores proper fit and helps prevent noise or binding.

• Provides structural support and alignment for the designated component
• Keeps parts seated securely to minimize movement and vibration during use
• A damaged or missing support can cause looseness, rattling, sagging, or misalignment
• Restores proper fit and function when the original is cracked, warped, or broken

• Disconnect power and shut off any gas/water supplies before servicing
• Refer to your model's parts diagram to identify location and orientation
• Install using the appliance's existing screws or clips; avoid overtightening to prevent damage
• Wear cut-resistant gloves; beware of sharp edges and pinch points

The Divertor Motor is an OEM part for Bosch dishwashers.  This part controls the direction of water flow within the unit. This motor directs the water to different spray arms based on the selected wash cycle, ensuring efficient cleaning by optimizing water usage and spray intensity. 

Causes of damage to the divertor motor can include regular wear and tear, exposure to water and detergent over time, and electrical issues such as wiring problems or faults in the control board.

Symptoms of a failing Divertor Motor include:

• Inadequate water distribution during cycles, which can lead to uneven cleaning results.
• The dishwasher making unusual noises, such as humming or grinding, which may indicate a struggle in the motor function.
• Certain wash zones receiving little to no water, affecting the appliance's overall performance.
• Error codes displayed on the dishwasher panel that relate to water circulation problems.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Lower rack wheel for Bosch dishwashers. Guides the bottom rack smoothly in and out. Replace if cracked, broken, or worn for proper rack operation.

This lock clamp secures an appliance component or assembly so it stays properly seated during operation. Replacing a worn or missing clamp helps restore a stable, rattle-free fit and reliable performance. What it does:

• Holds mating parts together to prevent shifting or vibration
• Helps maintain correct alignment of the secured component
• Can resolve issues where a part won't stay attached or seated
• Restore normal operation when the original clamp is broken or missing

• One lock clamp

• Disconnect power (and shut off water/gas if applicable) before servicing
• Note the clamp's original orientation; take a photo to aid reassembly
• Seat the component fully, then engage the clamp securely without over-stressing it
• Reassemble and test for a firm, stable fit before returning the appliance to service

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This sensor monitors the clarity and cleanliness of the wash water inside the dishwasher, helping the control board determine how dirty the water is and whether additional wash cycles are needed. It plays a key role in optimizing water usage and ensuring dishes come out clean. Replace this sensor if dishes are consistently coming out dirty, wash cycles are running too long or too short, or the dishwasher is not properly adjusting its cleaning performance.

Replace a broken, worn, or missing dishwasher leveling leg. This adjustable foot installs at the front corner to stabilize and level your appliance.

Lower housing that forms the structural base of your dishwasher. Replace when the original case is cracked, warped, or damaged to restore stability.

Dishwasher indicator light not working or staying on? This light signals cycle status and alerts. Common fix for control panel display issues.

Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.

Factory mounting screw secures panels, brackets, and internal components in your dishwasher. Replace missing, stripped, or damaged screws during repair.

Replace your cracked, bent, or missing dishwasher door handle. Restores a secure grip for easy opening and closing while improving appearance.

Fix loose or rattling dishwasher components with this holder retainer. Secures parts in position to prevent movement and restore quiet operation.