Bosch Dishwasher SHS63VL2UC Parts

Replace your broken or cracked dishwasher detergent dispenser door lid. This cover installs on the dispenser compartment to keep detergent secure.

Replace your dishwasher's upper rack pull-out rail assembly. Installs on top rack to enable smooth sliding. Needed when rails are cracked, broken, or wheels are worn. Includes left and right sides.

Fixes dishwasher leaking or overfilling issues. This overflow tube redirects excess water back into the drain path. Simple DIY repair part.

Trim strip finishes the exposed edge of your dishwasher where it installs. Replace if cracked, broken, or missing to restore a clean, finished look.

Does your dishwasher shake or make loud noises during the wash cycle? A worn suspension damper may be the cause. This part absorbs vibration and stabilizes the tub.

This cable harness routes power and signals between appliance control and components to restore reliable electrical connections. It replaces a damaged or worn harness to help eliminate intermittent operation and connectivity issues. What it does:

• Replaces the main wiring harness that links controls, sensors, and motors for proper electrical communication
• Restores reliable power and signal paths to correct intermittent power, non-responsive controls, or components that won't run
• Ensures secure connector mating to prevent arcing and poor contact
• Matches OEM connector types and wire lengths to fit in the original routing

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock
• Compare the new harness to the old one for connector types and routing before installation
• Handle connectors by the housings; do not pull on wires. Ensure all plugs snap fully into place

Replacement screw for securing dishwasher panels, trim pieces, and brackets. Restores proper fit when original screws are stripped, lost, or damaged.

Dishwasher repair set includes essential components for maintenance and fixes. Replace when parts show wear or damage. Verify fit with your model number.

This facia panel is the replacement trim for the dishwasher control area, restoring a finished appearance and protecting the underlying controls from daily wear. It's a direct-fit exterior panel designed to match the original finish. What it does:

• Replaces cracked, scratched, dented or discolored control-area trim to restore appearance
• Protects buttons, display and control housing from moisture, grease and debris
• Helps ensure the control assembly remains properly covered and aligned
• Prevents cosmetic wear from spreading to the door and control components

• One facia panel

• Disconnect power to the appliance before beginning any work to avoid shock
• Remove the outer door trim or control bezel per the appliance service instructions to access mounting points
• Reinstall fasteners carefully so the panel aligns with surrounding trim and operates without binding
• Test the door operation and control functions after reassembly

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Replace your dishwasher's outer door panel when the exterior finish is scratched, dented, or you're updating your kitchen's appearance. Mounts to front.

This insulating part provides a non-conductive, heat-resistant barrier between adjacent components inside the appliance. Replacing a damaged insulator helps prevent unintended contact and heat transfer, supporting safe, reliable operation and protecting nearby parts. What it does:

• Electrically isolates terminals or metal surfaces to help prevent shorts or arcing
• Reduces heat transfer to surrounding components
• Maintains proper spacing and support for the protected component
• Replace if the original is cracked, deformed, missing, or shows burn/discoloration

• 1 insulating part

• Disconnect power before servicing; shut off gas or water if applicable
• Access the component, note orientation/positioning of the original insulator, and transfer any clips or hardware as required
• Seat the new insulator fully and ensure no conductive parts touch unintended surfaces
• Reassemble, restore power, and verify normal operation with no rubbing, arcing, or overheating

Dishwasher mounting clip secures components in place. Replace if clip is cracked, broken, or missing to restore proper fit and stability of parts.