Bosch Dishwasher SHU66C07 Parts

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Dishwasher not draining or water pooling at bottom? A cracked sump disrupts water flow to the pump. This housing restores drainage and prevents leaks.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

Right side door hinge for dishwashers. Installs on the right side of the door frame. Replace if bent, broken, or damaged from door falling too hard.

Spring-style hose clamp secures water and drain hoses to fittings, preventing leaks. Replace when connections loosen or clips lose tension. Confirm fit with your model number.

Secures the sump assembly to the tub, preventing leaks and movement. Replace if worn, cracked, or if you notice water leaking from the base of your dishwasher.

Replacement adjuster socket for dishwasher leveling feet. Installs at cabinet base to raise or lower the unit for level installation. Replace if cracked or stripped.

This door handle replaces a worn or broken appliance door grip to restore a secure, comfortable surface for opening and closing. Designed to match the original fit and appearance for easy cosmetic repair. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, loose, or cosmetically damaged handles
• Restores proper leverage to reduce stress on the door latch and hinges
• Helps improve the look of the appliance by replacing a worn handle

• One door handle

• Refer to your appliance model's service manual for step-by-step removal and installation instructions
• Installation typically requires basic hand tools; disconnect power (and water if applicable) before servicing
• Handle may attach with screws or snap-fit clips—keep removed fasteners for re-use unless replacements are provided

This rubber gasket seals appliance openings to help prevent water and air leaks and restore proper door/tub sealing. It replaces a worn or damaged seal to reduce leaking and maintain normal appliance performance. What it does

• Creates a watertight/airtight barrier between mating surfaces to prevent leaks.
• Helps maintain operating temperature and efficiency by sealing the door/tub.
• Common symptom: visible water around the door or base during use.
• Common symptom: cracked, flattened, or distorted seal material that no longer compresses.
• Works as a direct replacement for the matching OEM seal when damaged or worn.

• One gasket as shown on the product page.

• Turn off power and water supply to the appliance before starting any repair.
• Remove the old seal carefully, clean the mounting channel of debris and residue, and inspect the mating surface.
• Press the new gasket evenly into the channel, starting at one corner and working around to ensure full seating without twists.
• Test the door closure and run a short cycle to confirm there are no leaks; re-seat if necessary.

This is a mechanical actuator that controls the opening of the detergent dispenser door during the wash cycle. It triggers the dispenser to release detergent at the correct time in the cycle. Replace this part if the dispenser door fails to open, detergent remains in the cup after a cycle, or dishes are not getting clean due to unreleased detergent.

Drain hose clamp

Left hinge cap for dishwasher door assembly. Replaces cracked, broken, or missing hinge caps. Cosmetic and structural part for door hinge cover.