Bosch Dishwasher SHV7PT53UC Parts

Structural support hinge for your dishwasher door. Installs on the side panel to allow smooth opening and closing. Replace if cracked or broken.

Fix dishwasher electrical issues with this cable harness. Resolves control panel malfunctions, display errors, and power connection problems.

This power control module (program) is the electronic control board that manages dishwasher power and cycle sequencing so the appliance runs selected programs reliably. It replaces a failed control module to restore normal control functions. What it does:

• Regulates power distribution to dishwasher components and manages program sequencing
• Helps resolve symptoms like no start, unresponsive controls, or cycles that won't advance
• Works with sensors and relays to initiate wash, drain and dry stages when functioning correctly
• Clears control-related error conditions when installed in good condition

• One power control module (program) as shown

• Disconnect electrical power at the breaker before attempting replacement
• Handle the module carefully; avoid static discharge and contact with circuit board components
• Transfer any harnesses or mounting hardware from the old module only if they match exactly

Power cord for dishwashers. Connects your dishwasher to the electrical outlet. Replace if damaged, frayed, or missing during installation or repair.

Fix leaks from your dishwasher's pump sump area with this repair kit. Restores proper water flow and stops leaking without replacing the entire pump assembly.

Mounting holder that secures internal dishwasher components in place. Replace if cracked, broken, or missing to restore proper support and alignment.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

This is a sensor that detects the level or presence of rinse aid in the dishwasher's dispenser system. It communicates with the control board to ensure the correct amount of rinse aid is dispensed during the wash cycle for spot-free drying. Replace this sensor if your dishwasher displays a rinse-aid error, fails to dispense rinse aid, or consistently leaves spots and film on dishes despite a full rinse-aid reservoir.

This insulating part provides a non-conductive, heat-resistant barrier between adjacent components inside the appliance. Replacing a damaged insulator helps prevent unintended contact and heat transfer, supporting safe, reliable operation and protecting nearby parts. What it does:

• Electrically isolates terminals or metal surfaces to help prevent shorts or arcing
• Reduces heat transfer to surrounding components
• Maintains proper spacing and support for the protected component
• Replace if the original is cracked, deformed, missing, or shows burn/discoloration

• 1 insulating part

• Disconnect power before servicing; shut off gas or water if applicable
• Access the component, note orientation/positioning of the original insulator, and transfer any clips or hardware as required
• Seat the new insulator fully and ensure no conductive parts touch unintended surfaces
• Reassemble, restore power, and verify normal operation with no rubbing, arcing, or overheating

This insulating part provides protective thermal and electrical insulation for internal appliance components, helping keep wiring and nearby parts separated and shielded. Replacing a damaged insulator restores safe spacing and reduces heat-related wear. What it does:

• Provides thermal and electrical isolation between components to help prevent heat transfer and accidental contact
• Protects wiring and nearby parts from chafing and abrasion
• Helps reduce risk of shorts or intermittent electrical faults when insulation is intact
• Common symptoms of a bad or missing insulator: visible damage, melting or scorch marks, exposed wiring, or intermittent operation

• Disconnect power to the appliance before servicing to avoid electric shock
• Remove any necessary panels to access the damaged insulator
• Handle carefully to avoid tearing or compressing the material; replace with the identical part number

Replacement door handle for dishwashers. Installs on the front panel to restore secure grip and smooth opening. Needed when original is cracked or broken.

Dishwasher making unusual noise or components overheating? This insulation shield acts as a thermal and electrical barrier, protecting wiring and reducing vibration contact. Simple DIY fix.

This insulating part protects and isolates components to help prevent electrical shorts and reduce heat transfer inside the appliance. It replaces a damaged or missing insulator to restore proper component spacing and safety. What it does:

• Provides electrical insulation between wiring or terminals to reduce risk of shorting or arcing.
• Helps maintain proper spacing and support for internal components.
• Reduces heat transfer to nearby parts and wiring.
• Commonly replaced when insulation is cracked, melted, missing, or after service that disturbs component placement.

• Disconnect power and unplug the appliance before attempting any repair.
• Verify correct orientation and fit before securing; do not force into place.
• Use only the replacement part specified for your appliance model.