Bosch Dishwasher SHX43RL5UC Parts

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.

Spring-style hose clamp secures water hoses to prevent leaks at connections. Replace if worn, rusted, or if you notice dripping around hose fittings.

Replacement dishwasher door handle that restores secure grip and appearance. Installs on the front panel. Replaces cracked, broken, or worn handles.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

Left side door hinge plate for your dishwasher. Replaces cracked, broken, or worn hinge plates that cause door misalignment or instability.

Protects dishwasher wiring from heat and abrasion. Replace if worn, cracked, or causing electrical shorts. Confirm fit with your model number.

Replace cracked, broken, or missing dishwasher rack roller wheels. Snaps onto bottom or top rack to restore smooth gliding. Easy DIY installation.

Replace your dishwasher's upper rack pull-out rail assembly. Installs on top rack to enable smooth sliding. Needed when rails are cracked, broken, or wheels are worn. Includes left and right sides.

Dishwasher cleaner removes grease, limescale, and odor-causing residue. Use monthly or when noticing buildup or smells. Confirm compatibility with your model.

Fix unresponsive or missing dishwasher buttons with this control panel push button set. Restores function selection and original panel appearance.

This replacement side panel restores the appliance's exterior finish and protects the cabinet edge from dings, scratches and wear. It's a direct-fit exterior trim piece that keeps the side of the unit looking finished and secure. What it does

• Covers and protects the appliance cabinet side from impact, scratches and cosmetic damage
• Restores a clean, factory appearance when original panel is dented, chipped or missing
• Helps maintain proper clearance and panel alignment with adjacent cabinetry
• Prevents exposed edges that can catch debris or snag clothing

• Includes: one side panel

• Disconnect power (and water supply if applicable) before starting work
• Handle panel carefully — edges may be sharp; gloves recommended
• Typically secured with screws or clips; retain hardware from the original panel or refer to the appliance parts diagram

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

This is a trim strip that attaches along the lower portion of the dishwasher door. It helps seal the door edge and provides a finished appearance to the front panel. Replace this piece if it is cracked, warped, or missing, which can lead to water leaks around the bottom of the door during wash cycles.