Bosch Dishwasher SHX5AVB5UC Parts

Fix a tilted or unstable dishwasher with this leveling leg. Ensures proper drainage and cleaning performance. Easy DIY install in minutes.

This replacement screw secures panels, brackets, and internal parts in your appliance for a tight, rattle-free fit. Use it to replace lost, stripped, or corroded hardware and keep components properly fastened.

• Fastens components to the appliance frame or assemblies
• Replaces a missing, stripped, or rusted original screw
• Helps reduce rattling or vibration from loose hardware
• Restores proper alignment of panels or brackets

• Disconnect power and shut off water before servicing
• Refer to your model's parts diagram to locate and place
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening

Fix a dishwasher that won't start, stops mid-cycle, or has unresponsive buttons by replacing the electronic control board. Restores all functions.

Replace a missing or damaged junction box cover on your dishwasher. Protects power supply and control board wiring connections. Easy DIY repair.

Replacement mounting bracket for dishwashers. Secures unit to countertops and cabinetry. Replace if bracket is cracked, broken, or missing from installation.

Fix a dishwasher that won't start, stops mid-cycle, or has error codes with this pre-programmed power module control board. Manages all wash functions.

Hardware washer distributes clamping force under screws and nuts in your dishwasher. Replace when worn or missing to restore secure fit and reduce vibration.

The Water Inlet Fill Hose is an OEM part for Bosch dishwashers. This part is responsible for safely and efficiently connecting the dishwasher to your home's water supply, ensuring that water flows into the dishwasher at the correct pressure and volume for optimal cleaning performance. 

Over time, the Water Inlet Fill Hose can become susceptible to wear and tear, leaks and blockages.

Symptoms indicating the need for a new Water Inlet Fill Hose include:

• Water pooling around the dishwasher base, pointing to a potential leak in the hose.
• The dishwasher not filling with water properly, or filling very slowly, suggesting a blockage or damage to the hose.
• A visible inspection reveals cracks, bulges, or signs of corrosion on the hose connectors.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replacement door spring for dishwashers. Restores proper tension to door mechanism. Needed when original spring is broken, worn, or stretched out.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Secures panels, brackets, and internal components in your dishwasher. Replace this screw if it's stripped, missing, or corroded to restore proper fit.

Replace your dishwasher's thermal insulation if experiencing excessive heat around the unit or noise during cycles. Protective barrier for safer operation.

Vent hose for dishwashers that guides steam and moisture out during wash cycles. Replace if cracked, disconnected, or worn to restore proper venting.

Secures panels, brackets, and trim pieces inside your dishwasher. Replace this fastener if stripped, missing, or damaged to restore tight assembly.

Replacement tube for Bosch appliances that routes water or drainage between components, helping restore correct flow, reduce pooling and leaks, and maintain normal appliance performance. What it does:

• Channels water between valves, pump and drain to enable normal water movement.
• Replaces cracked, split or blocked tubing that can cause leaks or standing water.
• Helps restore proper drainage and prevent water from pooling inside or under the appliance.

• Always disconnect power and shut off the water supply before servicing the appliance.
• Inspect and replace any damaged clamps, seals or fittings when installing the tube.
• Route the tube exactly as the original to avoid kinks; secure with the factory clamps or equivalent.

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment