Bosch Dishwasher SHX84AAF5N Parts

This replacement screw secures panels, brackets, and internal parts in your appliance for a tight, rattle-free fit. Use it to replace lost, stripped, or corroded hardware and keep components properly fastened.

• Fastens components to the appliance frame or assemblies
• Replaces a missing, stripped, or rusted original screw
• Helps reduce rattling or vibration from loose hardware
• Restores proper alignment of panels or brackets

• Disconnect power and shut off water before servicing
• Refer to your model's parts diagram to locate and place
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening

Fix a tilted or unstable dishwasher with this leveling leg. Ensures proper drainage and cleaning performance. Easy DIY install in minutes.

Fix a dishwasher that won't start, stops mid-cycle, or has unresponsive buttons by replacing the electronic control board. Restores all functions.

Fix a dishwasher that won't start, stops mid-cycle, or has error codes with this pre-programmed power module control board. Manages all wash functions.

Replacement cup rack for dishwashers. Installs inside the tub to hold cups and mugs during wash cycles. Replace if prongs are broken or plastic is cracked.

Replacement door spring for dishwashers. Restores proper tension to door mechanism. Needed when original spring is broken, worn, or stretched out.

Hardware washer distributes clamping force under screws and nuts in your dishwasher. Replace when worn or missing to restore secure fit and reduce vibration.

The Water Inlet Fill Hose is an OEM part for Bosch dishwashers. This part is responsible for safely and efficiently connecting the dishwasher to your home's water supply, ensuring that water flows into the dishwasher at the correct pressure and volume for optimal cleaning performance. 

Over time, the Water Inlet Fill Hose can become susceptible to wear and tear, leaks and blockages.

Symptoms indicating the need for a new Water Inlet Fill Hose include:

• Water pooling around the dishwasher base, pointing to a potential leak in the hose.
• The dishwasher not filling with water properly, or filling very slowly, suggesting a blockage or damage to the hose.
• A visible inspection reveals cracks, bulges, or signs of corrosion on the hose connectors.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replace your dishwasher's thermal insulation if experiencing excessive heat around the unit or noise during cycles. Protective barrier for safer operation.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Secures panels, brackets, and internal components in your dishwasher. Replace this screw if it's stripped, missing, or corroded to restore proper fit.

Vent hose for dishwashers that guides steam and moisture out during wash cycles. Replace if cracked, disconnected, or worn to restore proper venting.

Secures panels, brackets, and trim pieces inside your dishwasher. Replace this fastener if stripped, missing, or damaged to restore tight assembly.

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replace a broken, worn, or missing dishwasher leveling leg. This adjustable foot installs at the front corner to stabilize and level your appliance.

This factory screw secures appliance components per the original design, helping stop looseness and vibration. Replace a missing, stripped, or corroded fastener to restore a solid, rattle-free fit and protect nearby parts from damage.

• Secures panels, brackets, or internal components as specified by the manufacturer
• Helps maintain proper alignment and reduces vibration or rattling
• Replace if the head is stripped, threads are damaged, or the screw is missing
• Common signs include loose or misaligned panels/trim and hardware that won't stay tight

• Disconnect power and turn off water or gas supply as applicable before servicing
• Match length and thread to the original; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly without overtightening
• Retain any original washers, bushings, or clips used in the assembly