Bosch Dishwasher SHX87PW55N Parts

Replacement screw for securing dishwasher panels, trim pieces, and brackets. Restores proper fit when original screws are stripped, lost, or damaged.

Complete installation hardware set for dishwashers. Includes mounting brackets, screws, and fasteners needed to secure your dishwasher properly.

Exterior control panel face that restores the finished front surface. Replace if cracked, faded, scratched, or broken to restore appearance and access.

Dishwasher repair set includes essential components for maintenance and fixes. Replace when parts show wear or damage. Verify fit with your model number.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

This Program Power Control Module is the oven/dishwasher electronic control board that manages program selection and power delivery, restoring correct cycle operation and control response when the appliance fails to start or behave as expected. What it does:

• Controls program selection and timing signals so the appliance runs selected cycles
• Manages power distribution to subsystems to enable proper operation
• Commonly replaces a failed control board that causes no power, unresponsive controls, or interrupted cycles
• Works as the main interface between user commands and appliance functions

• 1 Program Power Control Module

• Disconnect power before attempting replacement to avoid shock or damage
• Handle the board by its edges and avoid touching components or contacts

This insulating part provides a non-conductive, heat-resistant barrier between adjacent components inside the appliance. Replacing a damaged insulator helps prevent unintended contact and heat transfer, supporting safe, reliable operation and protecting nearby parts. What it does:

• Electrically isolates terminals or metal surfaces to help prevent shorts or arcing
• Reduces heat transfer to surrounding components
• Maintains proper spacing and support for the protected component
• Replace if the original is cracked, deformed, missing, or shows burn/discoloration

• 1 insulating part

• Disconnect power before servicing; shut off gas or water if applicable
• Access the component, note orientation/positioning of the original insulator, and transfer any clips or hardware as required
• Seat the new insulator fully and ensure no conductive parts touch unintended surfaces
• Reassemble, restore power, and verify normal operation with no rubbing, arcing, or overheating

Replacement door handle for dishwashers. Installs on the front panel to restore secure grip and smooth opening. Needed when original is cracked or broken.

Dishwasher making unusual noise or components overheating? This insulation shield acts as a thermal and electrical barrier, protecting wiring and reducing vibration contact. Simple DIY fix.

Fix intermittent power or signal issues in your dishwasher with this internal connection cable. Restores electrical connection between components.

Dishwasher mounting clip secures components in place. Replace if clip is cracked, broken, or missing to restore proper fit and stability of parts.

This insulating part is a molded insulator that protects nearby components by reducing heat transfer and providing electrical isolation, helping prevent heat damage and short circuits for safer, more reliable appliance operation. What it does:

• Provides thermal insulation to limit heat transfer from hot components to surrounding parts
• Offers electrical isolation to help prevent shorts between conductors or grounded metal
• Maintains proper spacing and support for wiring or small assemblies
• Helps prevent symptoms such as scorch marks, melted wiring insulation, burning smells, or intermittent electrical behavior

• Disconnect power to the appliance before attempting any repair
• Inspect the surrounding area and the old insulator's location and orientation before removal
• Replace with the same part and orientation; avoid compressing or deforming the insulator

This operating module is the appliance control interface that routes user commands to the main control board, restoring keypad/console response and cycle selection. Replaces a failed or unresponsive control module to return normal panel operation. What it does:

• Receives inputs from the console and sends control signals to the main control board
• Restores responsive buttons, cycle selection, and user interface feedback
• Helps resolve symptoms like unresponsive controls, missing cycle selection, or intermittent panel behavior
• Does not include user-facing trim or external buttons unless listed separately

• One operating module

• High-level: disconnect power before servicing to avoid shock or board damage
• Handle the module by its edges and avoid static discharge; use an anti-static wrist strap if available
• Replace only if diagnostics indicate a faulty control module; verify connectors and wiring before swap