Bosch Washer WAW285H1UC Parts

Fix a washer that won't start or stops mid-cycle with a new door lock assembly. Common repair for doors that won't latch or unlock after the cycle ends.

Replace your washer door boot gasket if you notice water leaks during cycles or visible wear around the door seal. Verify fit with your model number.

Fix washer overfilling or not filling properly. This pressure sensor monitors water levels during wash cycles. Common repair for fill issues.

Leaking water around the inlet valve? This rubber inlet seal creates a watertight connection at your dishwasher's water inlet to stop drips and leaks.

Replace your washer flap to restore proper sealing and prevent rattles. This part covers openings in the assembly. Confirm fit with your model number.

This is a factory replacement set packaged under this part number. It provides matched components specified by the manufacturer to restore proper fit and function when the original set pieces are worn, missing, or damaged.

• Supplies the exact grouped parts designated for this repair
• Helps resolve issues caused by missing, loose, or broken components
• Supports correct assembly, alignment, or sealing as designed
• Common signs include rattling, misalignment, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Refer to your model's parts diagram for placement and orientation
• Handle sharp edges/components carefully; wear cut-resistant gloves
• Verify operation before final reassembly

Washer won't start or stops mid-cycle? This door lock assembly secures the door during operation, restoring proper locking and cycle completion.

This glass front panel replaces a cracked or damaged outer door surface to restore appearance and protect internal components. It provides the visible exterior surface for the appliance door and keeps the interior sealed from everyday wear. What it does:

• Replaces broken, cracked, or scratched outer door glass to restore the appliance's exterior
• Protects controls and internal layers behind the door from impact and debris
• Restores a smooth, easy-to-clean surface and original appearance
• Helps prevent sharp edges or glass fragments from exposing internal parts

• Handle carefully; wear cut-resistant gloves and eye protection to avoid injury from sharp edges
• Remove power to the appliance before starting any disassembly
• Follow OEM disassembly instructions for removing the door assembly and separating layers—do not force components
• If adhesive or clips are used, replace any damaged fasteners and allow adhesives to cure per manufacturer guidance

This oscillating system (C) is the replacement assembly that provides the controlled back-and-forth motion used by a driven component in compatible Bosch appliances, restoring proper movement and operation. What it does

• Transmits oscillating motion to a linked component to enable normal operation.
• Restores movement when the driven component is stuck, doesn't oscillate, or moves intermittently.
• Can reduce abnormal noise caused by a worn or damaged oscillating mechanism.
• Helps return consistent, even operation when oscillation is required for performance.

• One oscillating system (C) assembly.

• Disconnect power to the appliance before beginning any service.
• Access may require removing exterior panels or components; keep fasteners and small parts organized.
• Inspect surrounding parts (mounts, linkages) for wear and replace if damaged.

Replace your washer's access panel cover to restore proper enclosure protection. Shields internal components from debris and moisture. Confirm fit with your model number before ordering.

If your washer won't drain or water pools on the floor, a cracked or clogged drain hose is often the culprit. This hose channels wastewater to your drain.

Fixes washers with intermittent power, non-responsive controls, or component failures. This cable harness replaces damaged wiring to restore connections.

Fix washer not filling or slow fill with this inlet hose. Stops leaks at connection points and restores proper water delivery. Direct-fit replacement.

This agitator paddle is the replacement fin that helps move clothes through the wash cycle for better cleaning and even water distribution. It restores proper agitation action when the original paddle is worn or damaged. What it does:

• Channels water and clothing during agitation to improve wash performance
• Helps maintain balanced loads and reduces tangling during cycles
• Addresses symptoms like poor agitation, uneven cleaning, or visible damage to the paddle
• Works as a direct-fit replacement when the factory paddle is broken or missing

• Disconnect power and water before attempting any repair.
• Remove the agitator per the washer service manual; some models require a retaining bolt or spring clip.
• Inspect mating surfaces and fasteners; replace damaged clips or bolts as needed.

This is a water inlet hose that connects the household water supply to the dishwasher's fill valve. It delivers fresh water into the appliance during the wash and rinse cycles. Replace this hose if you notice leaking at the connection point, visible cracks, bulging, or if the dishwasher is not filling properly.