Bosch Dryer WTE84301 Parts

Dryer drum baffle lifts and tumbles clothes while circulating air evenly. Replace if cracked, loose, or causing noise. Verify fit with your model number.

Fix a dryer making loud noises or not tumbling with a new drum. This part holds clothes during the drying cycle and may rust, dent, or crack over time.

Tension roller for dryers. Mounts to the support bracket to maintain proper belt tension around the drum. Replace if worn, squeaking, or damaged.

This is a replacement seal used to restore a watertight connection and help prevent leaks in compatible appliances. It provides a simple, low-cost way to replace a worn or damaged sealing element. What it does:

• Creates a secure, leak-resistant barrier at the mating surfaces where installed
• Helps stop visible leaks and drip symptoms associated with damaged seals
• Restores intended sealing performance when original gasket or seal is deteriorated

• Inspect mating surfaces for damage or debris and clean before installing the new seal
• Make sure the seal seats evenly and is fully inserted into its groove or recess
• Replace only with the correct OEM part number for a proper fit
• Disconnect power and water supply and follow appliance safety procedures before servicing

Replacement mounting bracket holder that secures internal components in place. Install when original is cracked, broken, or missing to restore proper alignment.

Access panel cover that shields internal components from dust and moisture. Replaces cracked, broken, or missing exterior panels to restore finish.

Replacement drum taper cone for your dryer. This structural component secures the drum assembly. Order a new taper if yours is cracked or damaged.

This replacement seal restores a tight, leak-resistant connection between mating components inside your appliance. Replacing a worn seal helps stop drips at the joint and keeps the system operating reliably without nuisance leak faults.

• Forms a compressible barrier between parts to prevent leakage at a connection point
• Helps protect nearby components from moisture intrusion and corrosion
• Typical failure signs: moisture around a joint, puddling beneath the unit, or leak/overflow error messages
• Replace if the original is cracked, flattened, cut, brittle, or missing

• Disconnect power and shut off the water supply before servicing
• Access the connection, note the seal's orientation, and remove the old seal
• Clean mating surfaces; lightly moisten the new seal and seat it evenly without twisting or pinching
• Reassemble and test for leaks before reinstalling covers or panels

Replacement top lid cover for dryers. Protects internal components and restores finished appearance. Replaces cracked, broken, or missing lids.

This hose connection inlet provides the sealed connection point where the appliance's water inlet hose mates to the valve or tub, restoring a leak-free water feed and reliable flow for normal operation. What it does

• Connects the inlet water hose to the appliance inlet fitting or valve, directing water into the unit
• Creates a sealed joint to prevent drips and leaks at the hose connection
• Replaces cracked, worn, or damaged fittings that can cause visible leaks or reduced water flow
• Helps resolve symptoms such as water pooling under the appliance, continuous dripping, or inlet hose not seating properly

• One hose connection inlet

• Always disconnect power and shut off the water supply before starting work
• Inspect and replace any worn O-rings, gaskets, or clamps when installing this fitting
• Hand-start threads, then tighten clamps or fasteners to secure the hose; avoid over-tightening plastic parts
• After installation, restore water and power and check carefully for leaks during a short test cycle

This fill hose routes water from the supply or inlet valve to the appliance tub, restoring normal water flow for cycles that need filling. It's a direct-replacement hose designed to prevent leaks and ensure proper fill performance. What it does:

• Carries incoming water from the inlet valve to the washer/dish tub or dispenser
• Replaces cracked, split or collapsed hose that causes leaks or poor filling
• Helps stop continuous running or under-fill symptoms when the hose is damaged
• Restores a proper water path so fill cycles complete correctly

• One replacement fill hose

• Turn off water supply and power to the appliance before starting work
• Inspect and reuse or replace hose clamps; tighten securely to prevent leaks
• Route hose without kinks and ensure fittings match valve and tub connections

Replace your dryer door seal to stop air leaks and improve drying efficiency. Install when you notice tears, gaps, or lint escaping. Verify fit with your model.

Structural holder component for dryers. Secures internal parts in proper position. Replace if broken, cracked, or missing to restore proper fit.

This is a translucent cover that protects the drum light bulb inside the dryer. It snaps into place over the light assembly to shield the bulb from clothing and tumbling items while allowing light to illuminate the drum interior. Replace this cover if it is cracked, missing, or yellowed, which can leave the bulb exposed to damage or reduce visibility inside the drum.