Bosch Dryer WTE8630XEE Parts

This replacement seal restores a tight, leak-resistant connection between mating components inside your appliance. Replacing a worn seal helps stop drips at the joint and keeps the system operating reliably without nuisance leak faults.

• Forms a compressible barrier between parts to prevent leakage at a connection point
• Helps protect nearby components from moisture intrusion and corrosion
• Typical failure signs: moisture around a joint, puddling beneath the unit, or leak/overflow error messages
• Replace if the original is cracked, flattened, cut, brittle, or missing

• Disconnect power and shut off the water supply before servicing
• Access the connection, note the seal's orientation, and remove the old seal
• Clean mating surfaces; lightly moisten the new seal and seat it evenly without twisting or pinching
• Reassemble and test for leaks before reinstalling covers or panels

This fill hose routes water from the supply or inlet valve to the appliance tub, restoring normal water flow for cycles that need filling. It's a direct-replacement hose designed to prevent leaks and ensure proper fill performance. What it does:

• Carries incoming water from the inlet valve to the washer/dish tub or dispenser
• Replaces cracked, split or collapsed hose that causes leaks or poor filling
• Helps stop continuous running or under-fill symptoms when the hose is damaged
• Restores a proper water path so fill cycles complete correctly

• One replacement fill hose

• Turn off water supply and power to the appliance before starting work
• Inspect and reuse or replace hose clamps; tighten securely to prevent leaks
• Route hose without kinks and ensure fittings match valve and tub connections

This hose connection inlet provides the sealed connection point where the appliance's water inlet hose mates to the valve or tub, restoring a leak-free water feed and reliable flow for normal operation. What it does

• Connects the inlet water hose to the appliance inlet fitting or valve, directing water into the unit
• Creates a sealed joint to prevent drips and leaks at the hose connection
• Replaces cracked, worn, or damaged fittings that can cause visible leaks or reduced water flow
• Helps resolve symptoms such as water pooling under the appliance, continuous dripping, or inlet hose not seating properly

• One hose connection inlet

• Always disconnect power and shut off the water supply before starting work
• Inspect and replace any worn O-rings, gaskets, or clamps when installing this fitting
• Hand-start threads, then tighten clamps or fasteners to secure the hose; avoid over-tightening plastic parts
• After installation, restore water and power and check carefully for leaks during a short test cycle

Replace your dryer door seal to stop air leaks and improve drying efficiency. Install when you notice tears, gaps, or lint escaping. Verify fit with your model.

Structural holder component for dryers. Secures internal parts in proper position. Replace if broken, cracked, or missing to restore proper fit.

This is a translucent cover that protects the drum light bulb inside the dryer. It snaps into place over the light assembly to shield the bulb from clothing and tumbling items while allowing light to illuminate the drum interior. Replace this cover if it is cracked, missing, or yellowed, which can leave the bulb exposed to damage or reduce visibility inside the drum.

If your dryer isn't drying efficiently or has moisture buildup, the air channel may need replacement. Guides airflow for proper venting and performance.

This is the fan drum (blower wheel) that attaches to the motor shaft inside the dryer. It circulates heated air through the drum to dry clothes efficiently. Replace this part if your dryer is making unusual rattling or squealing noises, takes too long to dry clothes, or produces weak airflow from the exhaust vent.

Replace your dryer's duct if cracked, damaged, or missing. This duct channels air through the system for proper ventilation and efficient drying performance.

This is a dishwasher drain pump assembly that removes standing water from the tub so cycles can finish and dishes can drain properly. Direct-fit replacement for affected drain systems. What it does:

• Pumps wastewater from the dishwasher to the household drain during drain cycles
• Restores normal draining when a failed pump leaves water in the tub
• May correct symptoms such as standing water, cycle failures, or unusual pump noise
• Works with the dishwasher's drain hose and check valve to prevent backflow

• Disconnect electrical power and water supply before starting any repair.
• Confirm compatibility using your appliance model number; inspect seals and hose connections during replacement.
• Handle the impeller and motor housing carefully; avoid crushing wiring or connectors.
• Run a short test cycle and check for leaks after installation.

This replacement sheet is a protective metal panel that helps shield internal components and restore proper fit where the original panel is damaged or missing. It's a direct-fit repair part used in appliance body and interior assemblies. What it does:

• Shields internal wiring and components from contact, debris, and minor impacts
• Helps maintain proper airflow paths and component spacing inside the appliance
• Can reduce rattles or vibration caused by a loose or damaged panel
• Restores a finished appearance when the original sheet is bent, corroded, or missing

• Disconnect power (and water if applicable) before starting any repair
• Handle edges carefully; sheet metal can be sharp—wear gloves and eye protection
• Removal/replacement typically requires basic hand tools; follow the appliance service manual for exact fastener locations

Dryer door hinge provides the pivot point for smooth opening and closing. Replace if hinge is cracked, broken, worn from repeated use, or missing.