Bosch Dryer WTG865H4UC Parts

This replacement seal restores a tight, leak-resistant connection between mating components inside your appliance. Replacing a worn seal helps stop drips at the joint and keeps the system operating reliably without nuisance leak faults.

• Forms a compressible barrier between parts to prevent leakage at a connection point
• Helps protect nearby components from moisture intrusion and corrosion
• Typical failure signs: moisture around a joint, puddling beneath the unit, or leak/overflow error messages
• Replace if the original is cracked, flattened, cut, brittle, or missing

• Disconnect power and shut off the water supply before servicing
• Access the connection, note the seal's orientation, and remove the old seal
• Clean mating surfaces; lightly moisten the new seal and seat it evenly without twisting or pinching
• Reassemble and test for leaks before reinstalling covers or panels

Replacement control panel cover for your dryer. Installs on the front console to protect controls. Order if your cover is cracked, broken, or missing.

Replacement top lid cover for dryers. Protects internal components and restores finished appearance. Replaces cracked, broken, or missing lids.

Fix dryer control issues or motor problems with this metal paper capacitor. Stabilizes voltage for reliable electrical operation. Direct-fit part.

This hose connection inlet provides the sealed connection point where the appliance's water inlet hose mates to the valve or tub, restoring a leak-free water feed and reliable flow for normal operation. What it does

• Connects the inlet water hose to the appliance inlet fitting or valve, directing water into the unit
• Creates a sealed joint to prevent drips and leaks at the hose connection
• Replaces cracked, worn, or damaged fittings that can cause visible leaks or reduced water flow
• Helps resolve symptoms such as water pooling under the appliance, continuous dripping, or inlet hose not seating properly

• One hose connection inlet

• Always disconnect power and shut off the water supply before starting work
• Inspect and replace any worn O-rings, gaskets, or clamps when installing this fitting
• Hand-start threads, then tighten clamps or fasteners to secure the hose; avoid over-tightening plastic parts
• After installation, restore water and power and check carefully for leaks during a short test cycle

This fill hose routes water from the supply or inlet valve to the appliance tub, restoring normal water flow for cycles that need filling. It's a direct-replacement hose designed to prevent leaks and ensure proper fill performance. What it does:

• Carries incoming water from the inlet valve to the washer/dish tub or dispenser
• Replaces cracked, split or collapsed hose that causes leaks or poor filling
• Helps stop continuous running or under-fill symptoms when the hose is damaged
• Restores a proper water path so fill cycles complete correctly

• One replacement fill hose

• Turn off water supply and power to the appliance before starting work
• Inspect and reuse or replace hose clamps; tighten securely to prevent leaks
• Route hose without kinks and ensure fittings match valve and tub connections

Replace your dryer's door ring if it's cracked, broken, or missing. This structural component secures the door assembly for proper operation.

This coarse mesh dishwasher sump filter captures food particles to help prevent clogs and improve wash performance. It fits into the dishwasher sump to protect the drain pump and help maintain normal water flow. What it does:

• Traps food debris and larger particles before they reach the pump
• Helps reduce clogs that can cause standing water or slow draining
• Supports consistent wash performance by keeping spray arms and passages clearer
• Can help reduce smells caused by trapped food in the sump area

• Turn power to the appliance off before accessing the sump area
• Remove the lower rack and follow the OEM steps to lift out the old filter and seat the new one
• Inspect the surrounding sump and pump area for debris and clean as needed before installing

Replacement door window for dryers. Installs in the dryer door frame to provide visibility into the drum. Needed when original is cracked or broken.

Structural holder component for dryers. Secures internal parts in proper position. Replace if broken, cracked, or missing to restore proper fit.

If your dryer isn't drying efficiently or has moisture buildup, the air channel may need replacement. Guides airflow for proper venting and performance.

This is the fan drum (blower wheel) that attaches to the motor shaft inside the dryer. It circulates heated air through the drum to dry clothes efficiently. Replace this part if your dryer is making unusual rattling or squealing noises, takes too long to dry clothes, or produces weak airflow from the exhaust vent.

Replacement mounting bracket that secures dryer internal components. Needed when original bracket is cracked, broken, or missing to keep assemblies aligned.

Replace your dryer's worktop panel if it's cracked, chipped, or damaged. This top surface panel covers the control area and drum compartment.

Replace your dryer's control panel insert trim when cracked, worn, or damaged. Restores appearance and protects controls from spills. Confirm fit with model number.