Bosch Dryer WTL150 Parts

Thermister

Replacement leveling foot for dryers. Installs on the bottom corner to elevate and stabilize the appliance. Order if cracked, broken, or missing.

The Blower Belt is an OEM part for Bosch dryers. This belt efficiently transmits rotation from the motor to the blower fan, circulating heated air through the dryer drum.

Causes of a bad blower belt can include drying and cracking from heat exposure over many cycles.

Symptoms of a bad blower belt include:

• The blower fan not spinning or rotating slower than usual
• Longer dry times or an inability to fully dry clothes
• An intermittent squealing or squeaking noise from the belt

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Missing or damaged condensate drain hose? This dryer drain hose channels moisture from your condensation dryer to your household drain. Easy DIY fix.

Replacement drum belt wraps around the dryer drum and motor pulley to rotate the drum during drying. Replace if drum won't turn or tumble. Confirm fit.

This is an idler/tension roller pulley with built-in bearings that maintains proper tension on the dryer drum belt. It keeps the belt firmly engaged with the drum so it rotates smoothly during operation. Replace this part if the dryer is making squealing, thumping, or grinding noises, if the drum is not turning, or if the belt keeps slipping off.

Suspension spring for dryers. Supports the drum assembly and reduces vibration during operation. Replace if spring is stretched, broken, or missing.

Flexible seal that prevents heat loss and improves drying efficiency. Replace if torn, compressed, or causing loud thumping. Confirm fit with your model.

Replaces worn dryer drum bearings to restore smooth, quiet rotation and prevent tub damage. If you hear grinding or squealing, check compatibility.

Dryer door seal creates an airtight barrier to retain heat and improve efficiency. Replace if torn, cracked, or causing heat loss. Verify fit with your model.

Replacement door hinge for dryers. Supports and aligns the door for smooth opening and closing. Order when your hinge is broken, cracked, or bent.

This is a door hook or holder that latches the dryer door securely in the closed position during operation. It engages with the door strike or catch to keep the door from opening while the dryer is running. Replace this part if the dryer door won't stay closed, pops open during a cycle, or if the hook is visibly cracked or broken.

This mechanical door latch secures the dishwasher door during operation so cycles can run safely and the unit can seal properly. It replaces a worn or broken latch to restore reliable door closure and cycle starts. What it does:

• Physically holds and locks the door closed during wash cycles
• Triggers or maintains the door-closed state so the control will allow the cycle to start
• Commonly replaces units that are cracked, bent, or no longer latching
• Resolves symptoms like a door that won't stay closed, a dishwasher that won't start, or intermittent cycle interruptions

• Disconnect power to the appliance before beginning any repair
• Remove the inner door panel to access the latch; keep fasteners organized
• Inspect surrounding strike and mounting tabs for damage before installing

This genuine OEM replacement part is a pulley assembly for dryers. Sometimes called an idler arm, the pulley assembly keeps the dryer drive belt under tension as the belt wraps around the dryer drum. If the dryer is no longer spinning properly and is making a lot of noise, the pulley assembly may need to be replaced. Luckily this repair is a relatively simple process.To remove the old dryer pulley assembly, start by making sure the dryer is unplugged. Remove the lint screen from the top of the dryer. Remove the two Phillips screws by the lint screen opening. Depress the clips that hold the top cover down. Lift the top cover and keep it in an upright position. Disconnect the wire harness to the switch that separates the connector. Remove the screws on the front panel. Lift the panel forward and set it to the side. Next, lift the drum and locate the pulley assembly under the drum. Lift the belt off the motor pulley to remove the assembly. Set the new pulley assembly in the same position as the old one and make sure everything is aligned. Rotate the drum to make sure it rotates smoothly. reinstall the panels.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dryers.