Gaggenau Freezer RB472301 Parts

If your refrigerator cabinet feels warm or cooling is weak, the condenser fan may have failed. This fan circulates air over the condenser coil to remove heat.

This factory strip is a trim piece that finishes and protects an exposed edge or gap on your appliance. Replacing a cracked or missing strip restores a clean look and helps panels align and stay secure. What it does

• Finishes an exposed seam or edge as designed by the manufacturer
• Helps keep adjacent panels aligned and secure
• Can reduce vibration-related rattles when properly seated
• Common signs of failure: loose or missing trim, visible gaps, warping, cracks, or buzzing/rattling noises

• 1 strip

• Disconnect power and, if applicable, shut off water before servicing
• Note the strip's orientation; remove any screws/clips and gently release tabs
• Reuse or transfer original fasteners/clips as required by your model
• Align carefully and avoid overtightening to prevent damage to the strip or surrounding panels

Fixes unresponsive controls, display errors, or cycle failures in refrigerators and freezers. Direct replacement for failed main control modules.

This replacement strip restores a clean, factory fit where it's used on the appliance. Replacing a worn or missing strip helps secure adjoining pieces, maintain spacing, and eliminate unsightly gaps or vibration-related noise. What it does:

• Acts as a finishing/spacer strip between adjoining components
• Helps hold trim or panel pieces in the correct position
• Maintains alignment and clearances to prevent rubbing or rattling
• Common symptoms: cracked or missing strip, visible gap, loose trim/panel, buzzing or vibration noises

• 1 strip

• Disconnect power and, if applicable, shut off water before servicing
• Refer to your model's parts diagram for the correct orientation and attachment points
• Reuse original screws/clips if required; hardware is typically model-specific
• After installation, verify proper alignment and operation of adjacent panels/doors

This is a small wheel designed for use in a refrigerator or freezer, typically mounted on a shelf, drawer, or rack to allow smooth sliding in and out. It helps support the weight of stored items while enabling easy access. Replace this wheel if it is cracked, broken, or no longer rolling freely, causing drawers or racks to stick or sit unevenly.

Interior cabinet divider wall that restores proper compartment separation in your refrigerator. Replaces cracked, broken, or missing dividers.

This active carbon filter uses charcoal media to help control and reduce food odors inside the appliance, improving interior air quality and helping your fridge smell fresher between cleanings. What it does:

• Adsorbs and neutralizes common food and cooking odors circulating in the appliance interior
• Helps reduce lingering smells from strong foods like onions, fish, and cheeses
• Works with the appliance's air circulation system to maintain a fresher-smelling cavity
• Can help extend periods between intensive cleanings by reducing odor buildup

• Locate the filter access per your appliance owner's manual and remove the old filter before installing
• Slide or seat the new filter into the housing until it clicks or is secure; confirm proper orientation
• Replace filters according to the appliance manufacturer's recommended interval
• Dispose of used filters according to local regulations; avoid ingesting charcoal contents and wash hands after handling

If your freezer isn't maintaining proper temperature or runs constantly, the temperature sensor may have failed. This sensor monitors interior temps.

Factory trim strip that finishes edges and covers seams on your refrigerator. Replace if cracked, worn, or missing to restore clean appearance.

This is a filter drier used in the sealed refrigeration system to remove moisture and contaminants from the refrigerant lines. It is a small cylindrical component typically located along the refrigerant tubing between the condenser and the capillary tube. Replace this part if the refrigerator or freezer is not cooling properly due to a restricted or saturated drier, typically during a sealed system repair.

This rail guides a dishwasher rack so it slides smoothly in and out, restoring proper rack alignment and reducing jams. It's a direct-fit replacement when an original rail is bent, worn, or broken. What it does

• Guides the rack on its rollers to keep it level and aligned during loading and unloading
• Prevents the rack from binding or derailing while extending or retracting
• Helps restore smooth rack movement if the original rail is bent, cracked, or worn
• Works with the rack rollers and end stops to maintain safe, consistent operation

• One replacement rail

• Basic tools are usually all that's required; verify rail orientation before removing the old part
• Remove the affected rack and rollers as needed to access and replace the rail
• Inspect rollers and end stops while servicing; replace any damaged components for best results
• Disconnect power to the appliance before performing any service that exposes wiring or electrical components

This shock absorber cushions and controls dishwasher door movement to reduce slamming and improve closing action. It helps protect the door and cabinet from impact and can reduce noise during operation. What it does:

• Dampens and slows the dishwasher door as it opens and closes
• Helps prevent sudden drops or slamming that can damage the door or hinges
• Reduces vibration and noise caused by uncontrolled door movement
• Restores smoother, more controlled door operation when the original shock wears out

• One shock absorber

• Disconnect power to the appliance before beginning any repair
• Remove the dishwasher door panels or access panels to reach the mounting points
• Support the door during removal/installation to prevent it from falling or binding
• Use the OEM mounting hardware and verify secure attachment and correct alignment after installation

A single mounting screw used to secure appliance panels and components. This genuine replacement restores proper fastening to prevent loose trim, panels, or brackets and helps stop rattles or movement. What it does:

• Fastens panels, trim pieces, or internal brackets to the appliance frame
• Restores secure attachment where a screw is stripped, lost, or damaged
• Reduces vibration-related noise from loose panels or parts
• Works with the original threads and mounting points for correct fit

• One mounting screw

• Use the correct driver to avoid stripping the screw head
• Tighten until snug; do not overtighten to prevent damage to threads or panels
• Disconnect power and follow appliance safety guidelines before working on the unit
• If replacing multiple fasteners, verify all similar screws are the correct length and type

This fixture is the OEM replacement mounting piece designed to secure internal components and restore proper alignment and support. It helps keep parts stable for reliable operation and reduces noise caused by loose hardware. What it does:

• Secures internal panels or components to the appliance frame to prevent movement
• Restores proper alignment to reduce rubbing, vibration, or rattling noises
• Provides the correct mounting point for linked components to operate as intended
• Replaces damaged or missing fixtures that can cause part instability or failure

• Recommended for users comfortable with basic disassembly; unplug the appliance before starting.
• Keep fasteners and surrounding parts organized during removal to ensure correct reassembly.
• Inspect mating surfaces for damage or wear; replace adjacent hardware if needed.

Door hinge for refrigerators and freezers. Mounts between the cabinet and door to support proper swing and alignment. Replace if cracked or worn.