Kenmore Refrigerator 106.50272010 (10650272010, 106 50272010) Parts

A roll pin (spring pin) that secures rotating or sliding components by fitting into matched holes to hold shafts, levers, or brackets in place. Replaces a worn or damaged pin to restore proper mechanical engagement. What it does:

• Holds shafts, levers or hinges in position by expanding into drilled holes for a snug, vibration-resistant fit
• Keeps pulleys, rollers, or linkages from moving out of alignment or sliding off their shafts
• Common symptom: loose or wobbling pulley, lever, or shaft where the retaining pin is worn or broken
• Common symptom: noisy or intermittent operation caused by a pin that no longer secures moving parts

• Inspect mating holes and shaft for wear; replace pin with correct size to ensure secure fit
• Use appropriate pliers or a pin punch and hammer to drive the pin in or out; support the assembly to avoid damage
• Wear eye protection when installing or removing roll pins—pins can snap or fly out under force
• If pin is difficult to remove or install, consider using penetrating oil or heating only per OEM guidance

This ejector arm replaces the dispenser ejector that helps move detergent or rinse aid from the dispenser to the wash chamber for proper release during the cycle. Restores reliable dispensing and prevents missed or partial releases. What it does:

• Physically pushes or guides detergent/rinse into the wash chamber at the correct point in the cycle
• Replaces cracked, broken, or worn ejector arms that fail to move or sit correctly
• Addresses symptoms such as detergent not dispensing, dispenser door sticking, or visible damage to the ejector arm
• Works with the dispenser assembly to ensure consistent product release during operation

• Disconnect power to the appliance before starting any repair
• Remove the dispenser assembly per the service manual to access and replace the ejector arm
• Inspect surrounding dispenser components (hinges, springs, clips) and replace if damaged

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This is a replacement mounting screw used to secure appliance panels and small components. It provides a correct-fit fastener to restore secure attachment and eliminate rattles or loose parts. What it does:

• Secures trim, panels, brackets, or small assemblies to prevent movement and vibration
• Restores proper alignment when a worn or missing screw causes loose parts or noise
• Works as a direct-replacement fastener where the OEM screw specification is required

• One replacement screw

• Use the correct driver bit to avoid stripping the head; do not overtighten
• Disconnect power and follow appliance safety guidelines when accessing internal components
• If the original mounting hole or threads are damaged, repair or replace the mounting hardware before reinstalling

This wire assembly is the appliance wiring harness that connects controls and components to deliver power and signals. It restores reliable electrical connections and replaces damaged or frayed wiring to help your appliance operate safely. What it does:

• Routes power and control signals between components and the control board or switch
• Replaces broken, frayed, or burned wires that can cause intermittent operation or no power
• Helps stop electrical arcing and poor connections that may lead to erratic behavior
• Restores secure plug-and-socket connections for a stable electrical path

• One wire assembly (harness) as shown

• Always disconnect the appliance from power (unplug or switch off breaker) before starting
• Note wire routing and connector orientation or take photos to ensure correct reinstallation
• Handle connectors by the plug bodies, not the wires, and avoid pinching or stretching leads
• If you see heat damage or melted insulation on mating components, inspect and replace those parts as needed

This escutcheon is the outer trim piece that fits around the appliance's control area, restoring the finished appearance and helping keep controls and knobs properly seated. It replaces cracked, warped, or missing trim to improve safety and aesthetics. What it does:

• Covers and protects the control panel area from spills, grease, and damage
• Provides a finished surface for control knobs and switches to mount against
• Helps prevent controls from shifting or catching on clothing
• Common symptoms: visible cracks, warped or loose trim, exposed screw holes, or rough/sharp edges around controls

• Disconnect power to the appliance before beginning any work
• Remove control knobs and any retaining screws/panel fasteners to access the escutcheon
• Handle edges carefully; trim pieces and panels can have sharp edges
• Follow OEM instructions for reassembly and torque of fasteners

This air baffle directs airflow inside the appliance to help maintain proper ventilation and consistent operation. Replacing a worn or damaged baffle restores correct airflow routing and can reduce noise or uneven performance. What it does

• Guides internal airflow to support proper ventilation and component cooling
• Helps prevent turbulence that can cause noise during operation
• Supports even performance by keeping airflow directed where the OEM design intended
• Commonly replaced when cracked, warped, or missing

• Turn power (and gas, if applicable) off before beginning any repair
• Access may require removing panels or the drum/inner cavity
• Inspect surrounding mounting tabs and fasteners; replace any damaged hardware