Kenmore Refrigerator 106.51142110 (10651142110, 106 51142110) Parts

Fix uneven cooling or frost buildup in your refrigerator with this evaporator cover. Protects the evaporator coils and ensures proper airflow.

Ice buildup on evaporator coils? A failed defrost thermostat prevents proper defrost cycles. This bimetal sensor restores defrost heating on schedule.

Black door hinge for side-by-side refrigerators. Replaces cracked, broken, or worn hinges that cause door alignment issues or sagging doors.

Replace worn refrigerator door hinge cam bushings to restore smooth door swing and proper alignment. Fixes doors that don't close fully or seal correctly.

Lower front grille that covers the base opening of your refrigerator. Replace if cracked, broken, or missing to restore a finished look.

Supports and pivots your refrigerator door for smooth opening and flush closing. Replace if hinge is worn, damaged, or causing misalignment issues.

Main wire harness that routes power between the control board and components. Replace if wiring is damaged, burned, or connector clips are broken.

Graphite spray paint for appliance touch-ups. Covers chips, scratches, and scuffs on dryer drums, washer panels, and exterior surfaces. Restore finish.

This slide is the replacement rack glide that helps a rack roll smoothly in and out of the appliance, restoring proper rack movement and preventing scraping or sticking during use. Fits where the factory rack glide has worn or broken. What it does

• Provides a smooth track for a rack to slide in and out without binding
• Replaces cracked, worn or missing glide that causes rubbing or uneven movement
• Helps keep the rack properly aligned during loading and unloading
• Reduces noise and drag from a damaged or missing glide

• One replacement slide/rack glide

• Remove power supply or disconnect appliance before starting any repair
• Access the glide by sliding the rack out and removing any retainer clips or screws as required
• Snap or screw the replacement slide into place and verify smooth rack movement before restoring power
• If other rack parts are damaged, replace them to ensure proper function

This ice door support bracket holds and stabilizes the freezer ice door so it opens and closes smoothly and keeps the ice compartment sealed. Replaces a worn or broken support to restore proper door alignment and operation. What it does:

• Supports the ice door assembly to prevent drooping or misalignment
• Helps ensure the ice door opens and closes smoothly for reliable dispensing
• Reduces rattling or noise from a loose or damaged door support
• Prevents gaps that can lead to frost buildup or ice spillage

• Disconnect power to the appliance before starting any repair
• Remove the ice bin or door panel per service instructions to access the support
• Use common hand tools; handle plastic parts gently to avoid cracking
• Secure all fasteners; test door movement after installation

Black plastic corner cover replaces damaged or missing exterior trim on your refrigerator. Restores finished appearance and protects edges from wear.

This is a water supply tube that connects the internal water line to the dispenser spigot on the refrigerator, delivering water to the dispenser outlet. It ensures a steady flow of water when the dispenser lever is activated. Replace this tube if you notice leaking behind or under the dispenser, reduced water flow, or visible cracks and damage to the tube.

Secures the fan motor to its housing in your refrigerator. Replace this mounting clip if it's cracked, broken, or missing to restore proper alignment.

This small metal mounting clip secures the thermal fuse in place to maintain proper thermal contact and stable wiring. It helps keep the fuse positioned so the appliance can monitor temperature reliably and operate safely. What it does:

• Secures the thermal fuse to the appliance housing or duct to prevent movement
• Keeps the fuse in correct contact with temperature-sensing surfaces
• Helps prevent intermittent heating or thermal-sensor misreads caused by a loose fuse
• Useful when replacing a damaged or missing fuse retainer during fuse service

• One thermal fuse mounting clip

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove access panels per your model's service instructions to reach the fuse location
• Install clip in the same orientation as the original; use pliers if needed to seat it firmly
• Inspect the thermal fuse and wiring while installing; replace any damaged components per OEM guidance

This is a plastic air baffle that directs cold airflow from the evaporator fan into the refrigerator compartment. It helps ensure even cooling by channeling air to the proper areas within the cabinet. Replace this baffle if it is cracked, warped, or missing, which can cause uneven temperatures, frost buildup, or warm spots inside the refrigerator.