Kenmore Refrigerator 106.51149110 (10651149110, 106 51149110) Parts

Size: 1/4 inch.

This ice bin latch assembly secures the refrigerator's ice container so it stays seated and aligned with the auger drive. Replace a worn or broken latch to restore consistent ice dispensing and a snug fit.

• Locks the ice bin in place and aligns it with the auger/dispenser drive
• Helps prevent the bin from wobbling, shifting, or popping loose
• Can resolve no or intermittent ice dispensing caused by bin misalignment
• Direct replacement when the latch is cracked, worn, or missing

• Disconnect power to the refrigerator; turn off the water supply if needed
• Remove the ice bin to access the latch area
• Release retaining tabs/fasteners, note orientation, and install the new latch assembly
• Verify smooth latch engagement before reinstalling the bin and restoring power

This mounting plate assembly provides a sturdy base that keeps the appliance firmly secured and properly aligned with its supporting structure. Replace a bent, missing, or stripped plate to restore a safe, solid installation and reduce vibration.

• Secures and anchors the unit to its support surface or frame
• Maintains correct alignment and fastener locations for a stable fit
• Helps prevent vibration, shifting, sagging, or rattling during operation
• Replace if the plate is bent, cracked, rusted, or has stripped mounting holes
• Common signs include a loose or wobbly install, gaps, or difficulty tightening mounting screws

• Disconnect power before service; support the appliance while removing mounting hardware
• Fasten to solid backing (studs or approved anchors) using hardware specified for your model
• Level and align the plate with existing hole pattern before fully tightening
• Avoid overtightening and drilling into concealed utilities

Color: White

The Door Hinge is an OEM part for Whirlpool refrigerators. It acts as the pivot point that allows the fresh food door to open and close smoothly. As a moving component subjected to frequent use, the hinge can become loose or misaligned over time.

Causes can be normal wear and tear, excessive force on the door, or improper alignment over repeated use. Installation of this genuine replacement restores reliable door function.

Symptoms of a bad hinge include:

• The door not closing or sealing properly
• Difficulty opening and closing the door
• Noises or squeaking coming from the hinge area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black

Color: Mist Beige

This cam-door is the small plastic cam that helps the appliance door latch and move smoothly. Replacing a worn cam restores reliable door engagement and reduces slamming or misalignment. What it does:

• Guides and secures the door latch mechanism for proper opening and closing
• Helps align the door to prevent gaps or uneven sealing
• Reduces noisy or rough door movement caused by a worn cam
• Common symptom: door won't stay closed, feels loose, or binds when opening/closing

• One cam-door as shown

• Disconnect power (or unplug) before starting any repairs
• Access may require removing the outer door panel or trim—keep fasteners organized
• Handle small plastic parts carefully to avoid cracking; replace any damaged clips or screws

This humidity sensor housing holds and protects the fridge's humidity/control assembly, helping maintain proper humidity-sensing operation and reliable climate control. Designed to replace a cracked or damaged housing to restore proper sensor placement and protection. What it does:

• Secures and shields the humidity sensor and related control components
• Keeps the sensor correctly positioned for accurate humidity detection
• Prevents physical damage and moisture exposure to the sensor assembly
• Helps resolve symptoms like inaccurate humidity readings or loose sensor fit

• Disconnect power to the appliance before starting any repair
• Handle the humidity sensor carefully; remove and reinstall per manufacturer guidance
• Uses basic hand tools; refer to the service manual or OEM instructions for disassembly/reassembly steps
• Replace the affected components rather than reusing damaged parts

Replacement screw that secures panels, brackets, and other components inside your appliance, keeping assemblies tight and aligned. Replace missing or stripped hardware to eliminate looseness, reduce vibration, and restore a solid, factory-fit hold.

• Fastens panels, brackets, trim, or internal components
• Helps maintain alignment and reduce rattling/vibration
• Replaces missing, loose, rusted, or stripped hardware
• Common signs: stripped head/threads, loose panel, buzzing/rattling noises

• Disconnect power before service; shut off gas/water if applicable
• Match to the original screw; start threading by hand to avoid cross-threading
• Use the correct driver size to prevent stripping
• Tighten snugly; do not overtighten. If it won't hold, inspect the receiving hole/clip

This water connector is an inlet fitting that connects the household water line to the appliance, providing a secure path for water to reach the valve, dispenser or ice system. It helps maintain proper water flow and prevents leaks when installed correctly. What it does:

• Connects the incoming water supply to the appliance's inlet valve or ice/dispenser plumbing
• Provides a sealed transition between supply tubing and appliance fittings
• Restores normal water flow for ice makers and dispensers when damaged or corroded
• Can prevent dripping or pooling from a failing or broken connector

• Turn off the appliance power and shut off the house water supply before replacing
• Inspect and replace any worn tubing, O-rings, or clamps for a proper seal
• Hand-start threads to avoid cross-threading, then snug with a wrench—do not overtighten
• After installation, restore water and power and check all connections carefully for leaks

Color: White

Color: Black

A replacement machine screw with 8-32 threads used to secure panels and components on compatible Whirlpool appliances. Installs quickly to restore proper fit and stop rattling or loose parts. What it does:

• Secures panels, trim, brackets or components that use 8-32 machine-thread fasteners
• Restores proper alignment and prevents vibration-related noise
• Replaces missing, stripped, or damaged screws that allow parts to come loose
• Works where a standard 8-32 machine screw is specified by the manufacturer

• Disconnect power and/or gas before servicing the appliance to reduce shock or injury risk
• Use the proper screwdriver or nut driver for the screw head to avoid stripping
• Thread gently and stop when snug; do not overtighten to prevent stripping or damage
• If threads are damaged, replace with the correct-size screw rather than forcing it

This replacement pad cushions and isolates appliance components to reduce vibration, noise, and wear. It restores fit and helps keep parts stable for smoother, quieter operation. What it does

• Provides cushioning between parts to absorb shock and reduce rattling
• Helps maintain proper spacing and alignment of adjacent components
• Reduces vibration-transferred noise during operation
• Protects surfaces from wear where components contact each other

• One replacement pad

• Install in the location shown in your service diagram; part orientation may matter
• Clean mating surfaces before applying to ensure a secure fit
• Use basic hand tools as needed; follow OEM service instructions for your model
• Disconnect power and follow safety precautions before servicing electrical appliances